Parts for Frigidaire FEB798CCBC: 02 - Backguard Parts

This right backguard support secures the rear control/splash panel to the range, restoring a stable, flush fit and preventing rubbing or vibration. It's a direct replacement shaped for the right side of the backguard assembly. What it does:

• Holds the backguard/control panel steady at the rear of the range
• Prevents the backguard from sagging, vibrating, or rubbing against nearby components
• Restores proper alignment so controls and trim sit flush
• Helps eliminate rattling or movement when the cooktop is used

• One right backguard support bracket

• Disconnect electrical power (and gas, if applicable) before beginning work
• Remove backguard/control panel trim to access mounting points
• Use appropriate hand tools; avoid over-tightening fasteners to prevent damage
• Wear gloves and eye protection—metal edges may be sharp

This left-side backguard support bracket secures the oven/stove backguard to the range frame, restoring stability and correct alignment. It prevents the backguard from sagging or shifting and helps maintain a safe, finished fit at the rear of the appliance. What it does:

• Supports and anchors the left side of the rear backguard to the range cabinet
• Prevents the backguard from moving, rattling, or sagging during use
• Restores proper alignment so rear panels and controls fit securely
• Common symptom: loose or misaligned backguard or visible gap at the rear

• Disconnect power to the appliance before starting any repair
• Remove the backguard or access panel to reach mounting locations; keep hardware for reinstallation if reusable
• Align the bracket with existing mounting holes and secure using the original fasteners or OEM replacements
• Wear gloves to protect against sharp sheet-metal edges and verify secure fit before restoring power

This OEM part is a relay control board for ovens. An oven relay control board is a circuit board that receives signals from the main oven control board. The relay control board then relays the signal to regulate the oven's essential functions. Over time, a relay control board can become overworked. If the oven is no longer turning on, heating properly, or regulating its temperature, it might be time for a new relay board. Luckily, replacing this part is not a difficult process. To replace the relay board, make sure the oven is unplugged. Gain access to the upper back panel on the back of the range and remove the screws. Once the panel is removed access the relay board and remove the wire harness as well as any individual wires attached to the old board. Make sure to take note of the orientation of the wires. Replug the wires into their correct terminals on the new board and snap the new board back in place. Resecure the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore brand ovens.

This is a Frigidaire oven relay control board. This part is made for the double-oven wall design. The relay control board sends a signal to the main control board, causing the oven to turn on or off. These relay boards are engaged directly by the power button of the unit and the cooking timer. When the relay control board malfunctions or short circuits, the baking and broil functions will be directly affected. The oven may quit powering on altogether if the relay board completely fails. A short in the relay will cause the oven power to function correctly at random times. Wall ovens must be dismounted from their positions to install these parts. Once access is gained to the tear of the stove, the back panel can be removed. The relay control board is located near the bottom of the unit, close to the utility drawer. Unplug the connecting wires and engage the mounting clips holding the board. Discard the old unit, and replace it with the upgrade. Connect the cables and fasten the metal panel on the rear of the oven. Check for proper function before mounting the stove back into the wall.This is a genuine OEM product and is obtained directly from the manufacturer. This part is only compatible with Frigidaire wall ovens.

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This is an oval-head square-drive screw used to secure interior and exterior appliance components. It provides a low-profile finish and corrosion-resistant black finish for a neat, durable hold. What it does:

• Fastens panels, brackets, trim pieces, and other sheet-metal or plastic parts
• Oval head gives a slightly countersunk, finished appearance when installed
• Square (Robertson) drive resists cam-out for easier tightening
• Common replacement when original screws are stripped, missing, or corroded

• Use the correct square-drive (Robertson) bit to avoid stripping the screw head
• Hand-start the screw to ensure proper alignment before using power tools
• Do not overtighten; stop once the part is snug to avoid thread or panel damage
• Disconnect power and follow appliance safety precautions before servicing