Parts for Frigidaire FED367AQD: 03 - Backguard Parts

Color: Almond

Color: Almond

This part is a control board made by Frigidaire and is meant for use with ovens. If the current control board is defective in any way, this part can be used for repair or replacement.This part ensures the oven user can accurately monitor and control the temperature of the range. Over time, this part can easily become worn or rendered ineffective, making it difficult for the oven to function as intended. Work gloves are recommended for protection during any repair or replacement process. Make sure that the appliance is entirely disconnected from all power sources.This is an authentic OEM replacement part made of high-quality materials. This control board can be used with a variety of different oven models that have been manufactured by Frigidaire, Electrolux, Kelvinator, Gibson, and some other brands. This part is sold individually.

Color: Bisque

This surface element switch is the control behind your cooktop knob. It regulates power to the surface heating element so you can set and maintain the desired heat for reliable, consistent cooking performance.

• Regulates and cycles power to the surface heating element based on the knob setting
• Restores accurate low-to-high temperature control at the burner
• Typical failure symptoms: burner won't heat, only heats on high, or won't turn off
• Helps correct intermittent or uneven surface element heating

• Disconnect power at the circuit breaker before servicing
• Remove the knob and access the switch from the control panel or rear cover as applicable
• Photograph or label wire positions; transfer wires to the new switch one at a time
• Secure the switch, reassemble, restore power, and test all heat settings

The Range Switch is an OEM part for Frigidaire ranges. This switch controls the power supply to the range elements, allowing you to adjust the heat levels for cooking.

Causes of a bad Range Switch can include wear and tear from regular use, electrical issues such as short circuits or faulty wiring, or damage due to spills or overheating. These issues can result in the switch failing to regulate the power to the elements properly.

Symptoms of a bad Range Switch include:

• Inability to adjust the heat level
• The element not turning on or off
• Intermittent or inconsistent heating
• A burnt smell or visible damage on the switch

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

This is a 10-24 x 1/2 inch machine screw used to secure temperature probes, thermistor brackets, shields and drawer/box components. It provides a simple, reliable fastener for small appliance assemblies. What it does:

• Secures probe or thermistor brackets to the appliance chassis or housing
• Holds shielding or small drawer/box parts in place to prevent movement or rattling
• Helps maintain correct sensor positioning so temperature readings stay stable
• Common replacement when a stripped, corroded, or missing screw causes loose parts or vibration

• One 10-24 x 1/2 in. screw

• Use the matching 10-24 threaded hole; avoid over-tightening to prevent stripping or cracking nearby plastic
• If replacing a corroded screw, inspect mating threads and components for damage before reuse
• Turn off and unplug the appliance or disconnect power before accessing internal components

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts