Parts for Frigidaire FEF455WCBC: 02 - Backguard Parts

This selector switch controls the various heat or function settings on the range, allowing you to choose between different cooking modes or burner configurations. It mounts behind the control panel and connects to the wiring harness. Replace this switch if it fails to change settings properly, the knob turns without engaging, or the range does not respond when switching between functions.

Replace your range oven indicator light bulb when it burns out or dims. Restores visibility of oven status and control panel illumination. Verify fit with your model number before ordering.

Endcap for electric ranges. Covers and protects the end of a trim or component. Replace if cracked, broken, or missing to restore appearance.

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

This door retainer secures the door trim and inner door components to keep the appliance door aligned and stable. It restores proper door fit and prevents loose or rattling trim for safer, quieter operation. What it does

• Holds door trim/inner panel in place so the door closes and seals correctly
• Stops loose or vibrating trim that can cause noise or uneven gaps
• Helps maintain proper alignment to reduce strain on hinges and latches
• Common symptom: loose, misaligned, or rattling door trim

• One door retainer

• Disconnect power (or unplug) before starting any repair
• Remove door trim or inner panel per service instructions to access retainer
• Install the retainer in the same orientation; secure with the original fasteners

Mounting plate that secures the power cord set to the back of your range. Replace if the original plate is cracked, broken, or missing during installation.

This lower oven heat shield is a factory-style replacement panel that protects internal components from direct bake-broil heat and helps direct oven airflow for consistent cooking. Restores heat protection and prevents heat-related damage to nearby parts. What it does:

• Shields wiring, insulation and under-oven components from direct heat and hot spots
• Helps control internal oven heat flow for more even cooking
• Reduces risk of scorched or warped parts caused by excessive localized heat
• Common symptom: visible heat damage, burnt insulation, or a missing/warped shield

• Disconnect power (and gas supply if applicable) and allow the oven to fully cool before beginning work
• Handle carefully; edges may be sharp—wear gloves and eye protection
• Basic hand tools usually required; follow for exact fastener locations
• If corrosion or adjacent component damage is present, inspect and replace affected parts as needed

Replacement mounting screw for refrigerators, ovens, ranges, and cooktops. Secures interior panels, components, and trim. Needed when original is stripped, missing, or damaged during repair.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.