Parts for Frigidaire GCRE302CAFA: Backguard Parts

Protective cover that shields the range door hinge assembly from debris and damage. Replace if cracked, broken, or missing to restore a clean finished look.

This is a replacement door switch that signals the appliance when the door is closed so the unit will start or run. Restores proper door-sensing function for safe, reliable operation. What it does:

• Detects whether the door is closed and sends the on/off signal to the appliance control.
• Prevents operation when the door is open; stops cycles or disables functions if faulty.
• Commonly replaces a worn, broken, or non-responsive door actuator switch.
• Symptoms of a failing switch: appliance won't start, stops mid-cycle, or control behaves inconsistently.

• Disconnect power (unplug appliance or shut off the circuit) before attempting replacement.
• Handle electrical connectors carefully; match wiring and terminal positions during reassembly.
• Verify part compatibility with your model before installation.

Signals when your range burners or oven are active. Replace when light fails to illuminate or stays on constantly. Confirm fit with your model number.

Burner cap for electric and gas ranges. Covers the burner assembly on your cooktop. Replace if cracked, chipped, discolored, or missing for proper fit.

Small protective cap covers exposed range hardware to keep out dirt and moisture. Replace if cracked, broken, or missing to restore a finished look.

Replace your range backguard panel to shield control wiring from heat and grease while restoring appearance. Fits behind the control console. Verify fit with your model number.

Cosmetic overlay that covers and protects your range's control panel surface. Replace if scratched, cracked, peeling, or worn from kitchen use and spills.

Fix unresponsive buttons and display lights on your electric range with this control board. Controls oven and cooktop functions. 15-minute DIY repair.

Insulation pad installs between range components to dampen sound and reduce heat transfer. Replace if worn, torn, or missing to restore proper insulation.

Snap-in plug cap seals unused cabinet or component openings on your range. Replace if cracked, missing, or worn to keep out moisture and debris.

Replace a worn, cracked, or missing stainless control knob on your electric range. Fits keyed control shafts for temperature and function adjustments.

Indicator light lens covers and protects the burner signal light on your range. Replace when cracked, discolored, or missing. Confirm fit with your model.

Replace a faulty range surface element switch when your burner won't turn on or off properly. Common fix for unresponsive heating elements on ranges.

Top burner won't cycle temperatures or respond? This range burner control switch restores reliable heat regulation. Direct-fit replacement for electric and gas ranges.

Burner stuck on high or won't heat? This surface element switch controls temperature for electric range burners. DIY repair in under 30 minutes.

Replace a cracked, broken, or missing shield on your range. This protective guard component installs to safeguard internal parts from damage or wear.

Hearing rattling noises or concerned about exposed wiring? This protective shield guards internal range components from debris and contact. Simple DIY fix.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.