Parts for Kenmore 790.73439314 (79073439314, 790 73439314): Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

This is the adhesive graphic that labels the buttons on the electronic control panel. Replacing a worn, peeling, or unreadable overlay restores a clean look and makes the keypad labels easy to see again.

• Identifies control functions on the electronic oven/range panel
• Adheres to the control face; no electronics are included
• Common fix for worn-off text, bubbling/peeling edges, or cracked graphics
• Helps refresh the panel's appearance after damage or heavy cleaning

• Disconnect power to the appliance before starting
• Remove knob(s)/trim as needed to access the existing overlay
• Carefully peel off the old overlay and clean the surface of residue
• Align and apply the new overlay; press firmly to bond without bubbles

This control panel overlay is the adhesive label that sits over the electronic control, providing clear button legends and a clean, finished appearance. Replace a worn or damaged overlay to restore readable controls and protect the control face.

• Provides printed labels for keys and display so functions are easy to identify
• Covers and helps protect the electronic control surface from everyday wear
• Precisely aligns with the underlying touchpad/buttons for correct operation
• Typical replacement when the original overlay is faded, cracked, peeling, or missing

• Disconnect power to the appliance before servicing.
• Remove the control panel as needed. Peel off the old overlay and adhesive residue; clean and dry the surface.
• Align openings with the display and buttons, then apply from the center outward to avoid bubbles.
• Once adhered, the overlay cannot be repositioned; press firmly to secure.

The Clock/Timer is an OEM replacement part for Frigidaire ranges. It allows for precise time and temperature settings to be entered and displayed for oven functions.

As a digital module, causes for failure may include corrupted firmware over time or water/debris intrusion damaging circuits. Backlight failure is common after extended hours of usage.

Symptoms consist of:

• Inaccurate time displaying/keeping
• Timer functions like pre-heating not engaging
• Corrupted or non-responsive touch controls
• Faint or no display illumination

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.

You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.

Symptoms of a bad Range Switch Rocker include:

• The switch not responding when pressed
• Inconsistent or flickering performance of the heating elements
• Physical damage or looseness in the switch
• Intermittent operation or complete failure to activate the desired function

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Gas Range Knob is an OEM replacement part for Frigidaire gas ranges and cooktops. It serves as the interface for selecting and adjusting the heat level on gas burners through a simple turn mechanism. 

Symptoms of a bad gas range knob include:

• Difficulty turning the knob or slipping/jumping movements
• Knob appearing loose, cracked or damaged
• Inability to accurately select low heat settings  
• Burner flames not responding as expected to knob position

Causes can be attributed to normal wear over extended use as knobs are rotated frequently during cooking. Exposure to excessive heat or impacts may also degrade plastic knob components.

This OEM Frigidaire replacement is compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This replacement control knob restores easy, accurate selection of settings when your original is cracked, stripped, or missing. It attaches to the control shaft so you can adjust temperatures and functions as intended.

• Attaches to the control shaft to adjust heat, time, or function settings
• Replaces knobs that are cracked, loose, missing, or spin without engaging
• Helps when settings are hard to select or the indicator no longer lines up
• Restores a secure grip and consistent feel during operation

• Disconnect power before servicing; also shut off the gas supply
• Remove the old knob; if a set screw is present on your model, loosen it before pulling off
• Align the new knob with the shaft and press firmly until fully seated
• Verify smooth operation and correct indicator alignment after installation

This replacement control panel restores the appliance's front control surface to proper fit and appearance so buttons, switches, and the user interface mount securely for reliable operation and a finished look. What it does:

• Provides the mounting surface for control buttons, switches, and display assemblies
• Protects internal control components from spills and debris
• Restores a flat, undamaged front surface when original panel is cracked, dented, or warped
• Helps eliminate loose or misaligned buttons and improves user interaction

• Disconnect power to the appliance before beginning any work to avoid electrical shock.
• Handle edges carefully; metal panels can have sharp edges when removed.
• Transfer electronic components, buttons, or trim from the old panel per the service manual.

This outer door trim restores the finished edge and appearance of your appliance door. It replaces cracked, dented or missing trim to make the door look complete and help maintain proper alignment of adjacent parts. What it does:

• Covers and finishes the outer edge of the door for a factory appearance
• Helps hold adjoining panels and components in proper position
• Prevents sharp or exposed edges from being visible
• Common symptom: visible damage, dents, or loose/misaligned trim pieces

• Disconnect power to the appliance before starting any repair
• Remove any retaining screws or clips and handle trim and surrounding panels carefully to avoid damage
• Align trim into place and reinstall fasteners securely but do not overtighten
• If the trim attaches to glass or painted surfaces, use caution to avoid scratching

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Size: 8-18ab x 0.5 inch.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.