Parts for Kenmore 790.74134312 (79074134312, 790 74134312): Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

White

Black

Color: White

Color: White

Color: Black

This electronic control board manages the oven's heating functions and the clock/timer display. Replacing a failed controller restores accurate temperature control, reliable cooking modes, and a working display on your range or wall oven. What it does:

• Controls heating element relays based on user input and temperature sensor feedback
• Operates the digital display, clock, and kitchen timer
• Coordinates oven modes such as preheat, timed bake, and self-clean
• Common symptoms of a failing board: no heat or erratic temperatures, blank/unresponsive display, beeping or error codes, inability to start or cancel bake/broil

• 1 electronic control board (controller) assembly

• Disconnect power at the breaker before servicing; this board carries live voltage
• Access through the control panel; remove panels/screws as needed to reach the board
• Move wire connectors one at a time from the old board to the new; take photos for reference
• Use ESD protection and avoid touching circuitry; set the clock and test all oven functions after installation

A replacement control knob for appliance control panels that restores a secure, easy-to-turn interface for selecting temperatures and functions. Fits the original control shaft to make adjustments smooth and reliable. What it does:

• Replaces a cracked, stripped or missing control knob so you can accurately select oven/range settings
• Provides a clear pointer for the control shaft to indicate selected temperature or function
• Push-on design fits the appliance's splined control shaft for a snug, slip-free grip
• Common symptom fix: loose, spinning or missing knob that prevents changing controls

• Disconnect power to the appliance before servicing.
• Remove the old knob by pulling it straight off the control shaft; install the new knob by pushing it onto the splined shaft until fully seated.
• If the knob is tight or hard to remove, use a cloth for grip and pull straight; avoid excessive force that could damage the shaft.

The Gas Range Knob is an OEM replacement part for Frigidaire gas ranges and cooktops. It serves as the interface for selecting and adjusting the heat level on gas burners through a simple turn mechanism. 

Symptoms of a bad gas range knob include:

• Difficulty turning the knob or slipping/jumping movements
• Knob appearing loose, cracked or damaged
• Inability to accurately select low heat settings  
• Burner flames not responding as expected to knob position

Causes can be attributed to normal wear over extended use as knobs are rotated frequently during cooking. Exposure to excessive heat or impacts may also degrade plastic knob components.

This OEM Frigidaire replacement is compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This replacement control knob restores easy, accurate selection of settings when your original is cracked, stripped, or missing. It attaches to the control shaft so you can adjust temperatures and functions as intended.

• Attaches to the control shaft to adjust heat, time, or function settings
• Replaces knobs that are cracked, loose, missing, or spin without engaging
• Helps when settings are hard to select or the indicator no longer lines up
• Restores a secure grip and consistent feel during operation

• Disconnect power before servicing; also shut off the gas supply
• Remove the old knob; if a set screw is present on your model, loosen it before pulling off
• Align the new knob with the shaft and press firmly until fully seated
• Verify smooth operation and correct indicator alignment after installation

This front control panel provides the user interface cover for your appliance, restoring access to buttons and display and improving appearance when the original panel is cracked, faded, or damaged. Fits the factory OEM mounting points. What it does

• Replaces a cracked, broken, or worn front control panel so buttons and display are protected and accessible
• Restores the original fit and look of the appliance's control area
• Helps prevent dust and moisture from reaching electronic controls
• Useful when the existing panel is scratched, warped, or no longer secures properly

• Disconnect power to the appliance before starting any service
• Remove screws or clips holding the old panel and note screw locations for reinstallation
• Handle with care to avoid scratching the new panel and to protect any attached wiring or trim
• If panel attaches to switches or PCB, verify connections before powering on

This outer door trim restores the finished edge and appearance of your appliance door. It replaces cracked, dented or missing trim to make the door look complete and help maintain proper alignment of adjacent parts. What it does:

• Covers and finishes the outer edge of the door for a factory appearance
• Helps hold adjoining panels and components in proper position
• Prevents sharp or exposed edges from being visible
• Common symptom: visible damage, dents, or loose/misaligned trim pieces

• Disconnect power to the appliance before starting any repair
• Remove any retaining screws or clips and handle trim and surrounding panels carefully to avoid damage
• Align trim into place and reinstall fasteners securely but do not overtighten
• If the trim attaches to glass or painted surfaces, use caution to avoid scratching

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.