Parts for Kenmore 790.92659810 (79092659810, 790 92659810): Backguard Parts

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

The Indicator Light is an OEM part for Frigidaire ranges. This light is designed to signal when the range or oven is in operation, providing a visual cue for safety and usability. It typically illuminates when the burners or oven are on, ensuring users are aware of active heating elements.

Causes of a bad indicator light can include electrical malfunctions, wear and tear over time, or damage from power surges or excessive heat.

Symptoms of a bad indicator light include:

• Light not illuminating when the range or oven is in use
• Flickering or inconsistent illumination
• Light staying on constantly, even when the range or oven is off
• Visible damage or discoloration of the light

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This end cap is a fitted trim piece that replaces a worn or broken edge cover to restore the appliance's finished appearance and protect internal components from dust and contact. It's a simple cosmetic and protective repair. What it does:

• Covers and protects an exposed end or edge, preventing debris and accidental contact
• Secures adjacent trim or panels and helps keep them aligned
• Restores the appliance's original finished look where caps are cracked or missing
• Reduces the chance of snagging fabric or skin on a damaged edge

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Usually installs by aligning tabs and snapping into place; some applications may use one or two small screws
• Inspect surrounding trim for damage and replace any broken fasteners for a secure fit

This end cap is a small replacement trim piece that covers and protects the exposed edge of a cabinet, rail or appliance trim for a finished look and to prevent snags. It restores the original fit and appearance where the previous cap is cracked, broken or missing. What it does

• Covers an exposed end of a trim, rail or slide to prevent clothing or hands from catching
• Holds the trim edge in place and keeps debris out of the end opening
• Restores proper appearance when the original end cap is cracked, broken or lost
• Works as a direct-fit replacement when the OEM part number matches

• One end cap as shown

• Typically installs by snapping into place; no special tools required for most applications
• Verify orientation (left/right or top/bottom) before installing
• If the cap is part of a powered assembly, disconnect power before service
• Inspect mating trim for damage and clean the mounting area before fitting the new cap

This end cap is a small replacement trim piece that restores a finished edge and helps secure a refrigerator shelf or rail. It prevents catches and improves fit for worn or damaged trim pieces. What it does

• Covers and protects the exposed end of a shelf rail or trim piece to prevent snagging.
• Helps hold shelf or rail components in place for a flush, secure fit.
• Restores cosmetic appearance where the original end cap is cracked, missing, or worn.
• Simple, durable plastic construction suited for normal refrigerator use.

• One end cap as pictured and specified by the part number.

• Disconnect power to the appliance before servicing to avoid injury.
• Access may require removing the shelf, bin, or rail; keep track of any screws or clips.
• End caps generally press into place or secure with a small screw or clip—do not force; align then snap or fasten per the original mounting.

This snap-in plug seals a small cabinet or component opening to keep out moisture, debris and pests while preserving a finished appearance. It's a simple, low-cost replacement that restores proper sealing and fit. What it does

• Seals unused holes or access openings to prevent water, dust and pests from entering
• Restores a finished look where trim or panels have a missing cap
• Helps stop rattles from loose openings and reduces airflow where needed
• Works as a direct-fit replacement when the original plug is damaged or lost

• One snap-in plug

• Remove surrounding trim or panel per your model's service instructions to access the opening
• Press the plug into the hole until it snaps fully into place; no special tools normally required
• Always disconnect power to the appliance before doing any service that requires panel removal

The Indicator Light Lens is an OEM part for Frigidaire ranges. This component covers and protects the indicator light, which signals when a burner or the oven is on, providing a visual cue for users to ensure safe operation.

Over time, the indicator light lens can become damaged or discolored due to heat exposure, regular cleaning, or accidental impacts. Causes of a bad indicator light lens include cracking, warping, or clouding that obscures the light.

Symptoms of a bad indicator light lens include:

• The indicator light not being clearly visible
• Cracks or breaks in the lens
• Discoloration or cloudiness that diminishes the brightness of the light
• The lens becoming loose or falling off

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement switch completes the control circuit for a major appliance function, restoring user control and reliable operation. It mounts in the control panel and provides a durable rotary/infinite control interface. What it does:

• Makes or breaks the electrical connection for the corresponding control function
• Restores accurate control when the original switch is worn, intermittent, or unresponsive
• Can cause the related function to not start, stop unexpectedly, or fail to adjust when it fails
• Used in control panels where a rotary/infinite-type switch is required

• One replacement switch

• Disconnect power to the appliance before beginning any repair
• Verify correct switch orientation and secure mounting before reconnecting wiring
• Handle and route wires carefully; match terminal connections exactly to avoid damage

The Infinite Switch is an OEM component specifically designed for Frigidaire ranges. It controls the burners, allowing users to easily adjust heat levels and select different cooking zones. 

Causes of a bad infinite switch can include wear and tear over time, exposure to moisture or impacts from cookware, or underlying issues with the control board or wiring.

Symptoms of a bad infinite switch include:

• Burners failing to ignite or heat up when selected  
• Inability to change burner heat levels
• Flickering or non-responsive control panel lights
• Cooktop controls becoming unresponsive

Replacing the switch with this OEM Frigidaire part can help restore full functionality. It is compatible with freestanding and slide-in electric cooktop models. This replacement switch is also compatible with ranges sold under the Whirlpool, Roper, and Maytag brands.
 

The Small Surface Element Switch is an OEM replacement part for Frigidaire electric ranges. It serves as the control knob and circuitry to safely power one of the smaller cooking elements. 

Symptoms of a bad surface element switch include:

• Inability to ignite or regulate heating for its assigned zone
• Switch knob that feels loose, won't click smoothly, or won't stay set  
• Intermittent or unreliable power to the smaller element coils
• Tripped circuit breakers upon use that don't reset

Causes relate to thousands of rotations wearing micro-switches and wiring terminals within the control assembly. Regular cleaning around knobs can prevent accelerated deterioration from baked-on debris conducting excess heat.

This genuine OEM replacement part is compatible with other brands including Electrolux and Kenmore as well.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.