Parts for Ge DSKP333EC0WH: 01 - Backsplash, Cabinet & Front Panel Parts

Replacement dryer power cord that connects your dryer to the wall outlet. Needed when the original cord is damaged, burnt, frayed, or missing.

Caster wheel assembly for dryers. Installs at the base to provide mobility and stability. Replace if cracked, broken, or wheels no longer roll smoothly.

Front stabilizing leg for dryers. Installs at the front base to level and support the unit. Replace if cracked, broken, or missing to restore stability.

10-16 x 1-1/4 inch screw for securing dryer panels, brackets, and internal components. Replace missing, stripped, or damaged screws during repairs.

Dryer clip cover secures and protects internal components. Replace if broken, loose, or missing to ensure proper part retention and safe operation.

Mounting screw for dryer drum support and internal components. Replaces lost, stripped, or damaged screws during repairs. Package of 12 screws included.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

If your dryer's control panel is exposed or electronics aren't working properly, this control shield assembly protects and secures control components.

Dryer won't advance through cycles or stops mid-cycle? A failing timer disrupts cycle timing and start/stop control. Moderate difficulty replacement.

This door gasket seals the fridge/freezer door to maintain proper temperature and efficiency. Replaces a worn or torn seal to help reduce frost buildup and prevent cool air loss. What it does:

• Creates an airtight seal around the door perimeter to keep cold air in and warm air out.
• Helps prevent frost and ice buildup inside the compartment.
• Reduces compressor run time and helps maintain consistent internal temperatures.
• Common symptoms: visible gaps, torn or compressed seal, noticeable temperature fluctuations, or excess frost.

• Disconnect power before starting and work with clean, dry hands.
• Remove the old gasket by loosening retaining screws or pulling from the channel as applicable; inspect the channel for debris.
• Align the new gasket evenly and press into the door channel, working around the perimeter to ensure full contact.
• If needed, soften the gasket with warm water or a low-heat source per OEM guidance to help seat corners; avoid open flames.

Dryer won't start or humming when you press start? The door switch signals when the door is closed. Easy 15-minute DIY repair with basic tools.

Seals the gap between drum and bulkhead in your dryer. Replace when worn to eliminate scraping noises, prevent fabric snags, and maintain airflow.

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: metallic. It measures about 13-1/2 inches wide by 3 inches high by 3 inches deep.

Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.

Single replacement screw for securing dryer panels and internal components. Replaces lost, stripped, or damaged screws to restore proper fastening.

Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

Replace a cracked, broken, or missing dryer control knob. This dial attaches to the control panel and allows you to select cycles and settings.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.