Parts for Ge DSKP333EC0WW: 01 - Backsplash, Cabinet & Front Panel Parts

This cord set is a direct-replacement power cord that restores electrical connection to the appliance, letting it receive safe, consistent power when the original cord is damaged or worn. What it does:

• Provides the appliance's main AC connection so it can power on and operate
• Replaces frayed, cut, or melted cords that cause intermittent power or arcing
• Prevents unsafe wiring conditions from exposed conductors or loose connections
• Restores a secure plug/cable interface when the cord or plug is damaged

• One replacement cord set

• Always disconnect power at the breaker or unplug the appliance before replacing the cord
• Verify the replacement cord matches the original in wire count, connector type, and amp rating
• Tighten terminal screws securely and route the cord to avoid pinching or contact with hot components

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

Package of 12

This shield control is an electrical shield and control assembly that protects and secures the appliance's control electronics while helping ensure reliable operation. It replaces a worn or damaged shield to restore proper protection and alignment of the control components. What it does:

• Covers and shields control circuitry and wiring from debris, moisture, and physical contact
• Secures control components in the correct position to prevent loose connections
• Helps reduce risk of shorting or intermittent electrical faults caused by exposed electronics
• Common symptom: visible damage, cracked or warped shield, or control connections that appear loose

• One shield control assembly

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Handle the control area carefully and avoid touching circuit boards or connector pins
• Inspect connectors and wiring for damage; replace or reseat connectors as needed for proper fit

This timer and harness kit controls the sequence and duration of your dryer's cycles. Replacing a failing timer restores predictable cycle advancement and dependable start/stop operation so the dryer runs and shuts off on the settings you select.

• Advances the dryer through timed and automatic cycles
• Routes power to motor/heating circuits based on the cycle chosen
• Pre-terminated harness ensures correct, secure connections to the timer
• Common symptoms: timer won't advance or end, runs only on some settings, stops mid-cycle, or won't start when set

• Disconnect power by unplugging the dryer or switching off the circuit breaker
• Access the control panel; remove knob/dial if present and unfasten the old timer
• Move wiring connection-by-connection to the new timer/harness; route away from hot or moving parts
• Reassemble, restore power, and test cycle advancement

This door gasket seals the fridge/freezer door to maintain proper temperature and efficiency. Replaces a worn or torn seal to help reduce frost buildup and prevent cool air loss. What it does:

• Creates an airtight seal around the door perimeter to keep cold air in and warm air out.
• Helps prevent frost and ice buildup inside the compartment.
• Reduces compressor run time and helps maintain consistent internal temperatures.
• Common symptoms: visible gaps, torn or compressed seal, noticeable temperature fluctuations, or excess frost.

• Disconnect power before starting and work with clean, dry hands.
• Remove the old gasket by loosening retaining screws or pulling from the channel as applicable; inspect the channel for debris.
• Align the new gasket evenly and press into the door channel, working around the perimeter to ensure full contact.
• If needed, soften the gasket with warm water or a low-heat source per OEM guidance to help seat corners; avoid open flames.

The Door Switch is an OEM part for GE dryers, designed to ensure the dryer does not operate when the door is open. This safety feature is crucial for preventing accidents and ensuring the appliance operates efficiently and safely. The switch signals the dryer's control system about the status of the door—if it's open or closed—thereby allowing or preventing the start of a drying cycle. 

Causes of damage to the door switch often include mechanical wear from repeated use, accidental damage from loading or unloading, or electrical issues such as short circuits. 

Symptoms of a bad Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened
• Unusual noises or the dryer stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This felt seal creates a smooth, airtight barrier where the drum meets the bulkhead in your dryer. Replacing a worn seal helps maintain proper airflow, protect fabrics from snagging, and reduce scraping or squealing noises during operation. What it does:

• Seals the gap between the rotating drum and front/rear bulkhead to contain heat and airflow
• Provides a low-friction, cushioned surface for the drum rim
• Helps keep lint and debris out of the cabinet
• Common symptoms of failure: longer or uneven dry times, rubbing/scraping noises, clothes catching or leaving marks at the drum edge, visibly worn or torn felt

• 1 felt seal

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the top/front panel to access the drum and bulkhead; support drum as needed
• Remove old felt and adhesive; clean the mating surface thoroughly
• Dry-fit the new seal; install per manufacturer guidance; allow proper set time before reassembly
• Hand-rotate the drum to verify even contact and clearance, then test operation

The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance. 

Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching. 

Symptoms of a bad Door Latch include:

• The dryer door doesn't stay closed during cycles.
• Difficulty in starting the dryer due to the door not activating the safety switch.
• Visible wear or damage to the latch mechanism.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Dryer Bearing Slide (2-Pack) is an OEM replacement part for GE dryers. These slides are installed on the front panel of the dryer and support the drum as it rotates. They help reduce friction and wear, ensuring smooth and quiet operation during drying cycles. This pack includes two bearing slides, which are commonly used together in the dryer assembly.

Over time, bearing slides can wear down due to regular use, heat, and friction. When they become worn or damaged, the drum may no longer rotate smoothly, which can affect the dryer's performance and increase noise levels.

Symptoms of bad dryer bearing slides include:

• A loud squeaking or scraping noise during operation
• Difficulty rotating the drum manually
• Clothes taking longer to dry due to improper drum movement
• Visible wear or thinning on the existing slides

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: metallic. It measures about 13-1/2 inches wide by 3 inches high by 3 inches deep.

This Lint Screen Cover is an original and genuine OEM replacement part for GE dryers. The Lint Screen Cover plays a role in the efficient operation of your dryer. It serves as a protective grid that helps prevent objects from entering the dryer vent and causing potential damage to the internal components.

One common cause is a build-up of lint or debris, which can restrict proper airflow and result in overheating. This can lead to reduced drying efficiency, longer drying times, and potential damage to other components of the dryer.

Here are some symptoms that indicate a faulty Lint Screen Cover:

• Excessive lint accumulation around the dryer vent area
• Restricted airflow and poor drying performance
• Overheating of the dryer
• Unusual noises during operation
• Visible damage or deformation of the grid structure

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This is a single replacement screw used to secure appliance panels and components. It provides a direct one-for-one replacement to restore proper fastening and help eliminate rattles or loose panels. What it does

• Secures trim, access panels, or internal components to prevent movement and vibration.
• Replaces stripped, missing, or corroded screws that cause loose or rattling parts.
• Restores proper alignment so doors, drawers, or panels close and sit correctly.
• Helps maintain safe, stable operation by keeping components fastened.

• Handle with care and use the correct screwdriver to avoid stripping the head.
• Tighten to a snug fit; do not over-torque which can strip threads or crack plastic.
• If the original screw was damaged or the mating thread is stripped, inspect the hole and replace with the correct OEM screw or insert as needed.
• Disconnect power or follow appliance-specific safety steps before accessing internal parts.

This Lint Screen Cover is an original and genuine OEM replacement part for GE dryers. The Lint Screen Cover plays a role in the efficient operation of your dryer. It serves as a protective grid that helps prevent objects from entering the dryer vent and causing potential damage to the internal components.

One common cause is a build-up of lint or debris, which can restrict proper airflow and result in overheating. This can lead to reduced drying efficiency, longer drying times, and potential damage to other components of the dryer.

Here are some symptoms that indicate a faulty Lint Screen Cover:

• Excessive lint accumulation around the dryer vent area
• Restricted airflow and poor drying performance
• Overheating of the dryer
• Unusual noises during operation
• Visible damage or deformation of the grid structure

This genuine GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.

Symptoms of a failing Door Strike include:

• The dryer door not staying closed during a cycle
• Difficulty in closing the dryer door or getting it to latch properly
• The dryer not starting because the door switch is not engaged
• Visible damage or wear on the door strike

Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: If the door catch is also needed, use part number WE1M1011.

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly and stays aligned. A worn or bent hinge can lead to door sagging, scraping, or poor latching that impacts performance and safety. What it does

• Supports the door and provides the pivot point for opening/closing
• Maintains door alignment to help ensure a proper seal
• Restores smooth, consistent door motion
• Common symptoms: door sags, squeaks, scrapes, or won't latch/stay closed

• 1 hinge

• Disconnect power before servicing; for gas units, also shut off gas supply
• Support the door while removing/installing fasteners to prevent stress on the panel
• Reuse original mounting screws/hardware unless damaged
• After installation, adjust if needed

The Timer Knob is an OEM part for GE dryers. It is a component that allows users to select and control the drying cycles and settings on their dryer. Designed with durability and ease of use in mind, this knob fits directly onto the timer shaft, providing a reliable interface for setting the dryer's timer. 

Over time, the timer knob can become worn or damaged due to frequent use or accidental impacts. A malfunctioning knob may not engage properly with the timer shaft, making it difficult or impossible to set the dryer cycle. 

Symptoms of a bad Timer Knob include:

• Difficulty in turning the knob or setting the dryer timer
• The knob slipping or failing to engage with the timer shaft
• Cracks or breakage on the knob itself

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

A replacement screw used to secure panels and components in compatible GE appliances. Replacing missing or damaged screws restores secure mounting, reduces rattling, and helps keep parts aligned during normal operation. What it does:

• Fastens panels, trim, brackets, or small appliance components to maintain proper alignment and fit.
• Keeps internal parts secured to reduce vibration, rattling, or movement during use.
• Replaces stripped, rusted, or missing hardware that can cause loose or misaligned panels.
• Small, non-electrical part — does not affect electrical circuits or controls.

• Disconnect power and unplug the appliance before accessing internal parts.
• Use the properly sized screwdriver to avoid stripping the head; hand-start threads to prevent cross-threading.
• Tighten securely but avoid over-torquing; overtightening can strip threads or damage plastic components.
• Keep track of small parts and hardware; replace any damaged or mismatched screws with the correct OEM part.