Parts for Bosch WTE86300US/03: Base Assembly Parts

Replacement leveling foot for dryers. Installs on the bottom corner to elevate and stabilize the appliance. Order if cracked, broken, or missing.

Dryer won't start or drum won't turn? A faulty motor assembly is often the cause. This part powers both the drum and blower. Moderate difficulty repair.

Suspension spring for dryer drum support system. Installs between the drum and cabinet to absorb vibration. Replace if stretched, broken, or missing.

Tension roller for dryers. Mounts to the support bracket to maintain proper belt tension around the drum. Replace if worn, squeaking, or damaged.

Drive belt transfers power from motor to drum to tumble clothes. Replace if dryer drum won't turn or makes squealing noises. Confirm fit with your model.

This is the fan drum (blower wheel) that attaches to the motor shaft inside the dryer. It circulates heated air through the drum to dry clothes efficiently. Replace this part if your dryer is making unusual rattling or squealing noises, takes too long to dry clothes, or produces weak airflow from the exhaust vent.

This is a blower wheel that mounts inside the dryer's blower housing and circulates heated air through the drum during the drying cycle. It is driven by the drive motor and pushes air through the lint filter and exhaust vent. Replace this part if your dryer takes too long to dry clothes, makes squealing or rattling noises from the blower area, or fails to circulate air properly.

Fix dryer control issues or motor problems with this metal paper capacitor. Stabilizes voltage for reliable electrical operation. Direct-fit part.

Replacement top lid cover for dryers. Protects internal components and restores finished appearance. Replaces cracked, broken, or missing lids.

Fix F03 error code or water leaking from your dryer. This condensation pump removes water during the drying cycle. Moderately easy DIY repair.

This hose connection inlet provides the sealed connection point where the appliance's water inlet hose mates to the valve or tub, restoring a leak-free water feed and reliable flow for normal operation. What it does

• Connects the inlet water hose to the appliance inlet fitting or valve, directing water into the unit
• Creates a sealed joint to prevent drips and leaks at the hose connection
• Replaces cracked, worn, or damaged fittings that can cause visible leaks or reduced water flow
• Helps resolve symptoms such as water pooling under the appliance, continuous dripping, or inlet hose not seating properly

• One hose connection inlet

• Always disconnect power and shut off the water supply before starting work
• Inspect and replace any worn O-rings, gaskets, or clamps when installing this fitting
• Hand-start threads, then tighten clamps or fasteners to secure the hose; avoid over-tightening plastic parts
• After installation, restore water and power and check carefully for leaks during a short test cycle

Replace your dryer's cracked or missing protective housing cover. Shields internal components from debris and moisture. Direct fit into original mounting.

Access panel cover that shields internal components from dust and moisture. Replaces cracked, broken, or missing exterior panels to restore finish.

This is a cover lid for the storage compartment on a dryer. It protects the storage area and keeps it enclosed when not in use. Replace this part if the lid is cracked, broken, missing, or no longer stays securely in place.

Dryer won't start or stops mid-cycle? A faulty door latch prevents operation. This mechanical lock assembly ensures your door closes and latches securely.

This is a heat exchanger filter assembly used in condenser dryers. It helps recover heat from the exhaust air and condense moisture so the dryer can operate without an external vent. Replace this part if drying times have increased significantly, the dryer is overheating, or the unit is not properly removing moisture from clothes.

Missing or damaged condensate drain hose? This dryer drain hose channels moisture from your condensation dryer to your household drain. Easy DIY fix.

Replacement mounting bracket holder that secures internal components in place. Install when original is cracked, broken, or missing to restore proper alignment.

This replacement sheet is a protective metal panel that helps shield internal components and restore proper fit where the original panel is damaged or missing. It's a direct-fit repair part used in appliance body and interior assemblies. What it does:

• Shields internal wiring and components from contact, debris, and minor impacts
• Helps maintain proper airflow paths and component spacing inside the appliance
• Can reduce rattles or vibration caused by a loose or damaged panel
• Restores a finished appearance when the original sheet is bent, corroded, or missing

• Disconnect power (and water if applicable) before starting any repair
• Handle edges carefully; sheet metal can be sharp—wear gloves and eye protection
• Removal/replacement typically requires basic hand tools; follow the appliance service manual for exact fastener locations

This is a heat exchanger filter assembly used in condenser dryers. It helps recover heat from the exhaust air and condense moisture so the dryer can operate without an external vent. Replace this part if drying times have increased significantly, the dryer is overheating, or the unit is not properly removing moisture from clothes.