Parts for Kitchenaid KP26M1XVB5: Base And Pedestal Unit Parts

Need an extra mixing bowl for batch cooking or quick ingredient swaps? This stand mixer bowl locks securely in place. Easy 5-minute swap—no tools needed.

Fix a mixing bowl that won't lock in place or keeps sliding during use. This retaining pin secures the bowl clip to keep your bowl firmly seated.

If your mixer bowl won't stay in place or wobbles during mixing, this retainer clip secures it properly. Simple DIY fix takes just minutes to install.

Mounting screw secures internal brackets and panels in mixers. Replace if missing, stripped, or damaged to prevent loose components and rattling.

Rubber foot for stand mixer base. Replaces worn, cracked, or missing feet. Stabilizes mixer, reduces vibration, and protects countertops.

Fix mixer parts that shift or make noise with this retaining ring. Snaps into groove to secure components on shaft. Takes under 20 minutes to install.

Lift arm rod for stand mixers. Connects the lift handle to the bowl support mechanism. Replace if bent, stripped, or the lift assembly is jammed.

This replacement spring restores proper tension and return action within the original mechanism of your appliance. Replacing a fatigued or broken spring helps moving parts operate smoothly and return to position for consistent, reliable performance.

• Supplies controlled tension within the assembly
• Returns levers or linkages to their neutral position after use
• Helps maintain proper alignment and engagement of moving parts
• Common signs of failure: weak/loose feel, parts not returning, intermittent operation, rattling or squeaking

• Disconnect power before service; also shut off gas/water
• Note original routing and attachment points; take a reference photo before removal
• Use needle-nose pliers or a spring tool; avoid overstretching the new spring
• Verify smooth manual movement before reassembly and testing

Small flat washer for KitchenAid stand mixers. Installs between mechanical components to ensure proper spacing. Replace if worn, cracked, or missing.

Threaded nut secures panels, brackets, and internal assemblies in your stand mixer. Replace if missing, stripped, or damaged to restore secure attachment.

Upgrade or replace your mixer's paddle with this coated flat beater in Silent Silver. It restores smooth, even mixing performance for everyday recipes and is designed in the narrow profile specified for select stand mixers.

• Blends ingredients thoroughly for batters, doughs, and mashed mixtures
• Direct replacement for a beater that is bent, chipped, peeling, or missing
• Narrow profile mates correctly with the intended mixer hub style

• Unplug the mixer before attaching or removing the beater
• Tilt the head up or lower the bowl; align the beater slot with the shaft pin, push up, and twist to lock
• Clean and dry per the manufacturer's care instructions before first use

Plastic lift arm that raises and lowers the mixing bowl on stand mixers. Replace if cracked, broken, or worn from frequent use and age.

Replace your bent, worn, or broken wire whip attachment for KitchenAid stand mixers. Essential accessory for whipping cream and egg whites. 5-quart capacity.

Fix a mixer that won't engage or slips during operation. This cam restores proper mechanical linkage timing. Straightforward DIY replacement part.

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

If your mixer's bowl lift handle is cracked or missing, this rotating handle restores convenient bowl access. Simple installation—no tools needed.

Replacement mounting screw for stand mixer panels, brackets, and trim. Secures internal components to keep parts aligned. Replace if missing, stripped, or rusted.