Parts for Kitchenaid KSMC895OB1: Base And Pedestal Unit Parts

Replace your cracked or missing 8-quart stainless steel mixing bowl. Features a J-hook handle for easy hanging and stacking. Dishwasher-safe design.

If your mixer bowl won't stay in place or wobbles during mixing, this retainer clip secures it properly. Simple DIY fix takes just minutes to install.

Mounting screw secures internal brackets and panels in mixers. Replace if missing, stripped, or damaged to prevent loose components and rattling.

Rubber foot for stand mixer base. Replaces worn, cracked, or missing feet. Stabilizes mixer, reduces vibration, and protects countertops.

Fix mixer parts that shift or make noise with this retaining ring. Snaps into groove to secure components on shaft. Takes under 20 minutes to install.

Lift arm rod for stand mixers. Connects the lift handle to the bowl support mechanism. Replace if bent, stripped, or the lift assembly is jammed.

This replacement spring restores proper tension and return action within the original mechanism of your appliance. Replacing a fatigued or broken spring helps moving parts operate smoothly and return to position for consistent, reliable performance.

• Supplies controlled tension within the assembly
• Returns levers or linkages to their neutral position after use
• Helps maintain proper alignment and engagement of moving parts
• Common signs of failure: weak/loose feel, parts not returning, intermittent operation, rattling or squeaking

• Disconnect power before service; also shut off gas/water
• Note original routing and attachment points; take a reference photo before removal
• Use needle-nose pliers or a spring tool; avoid overstretching the new spring
• Verify smooth manual movement before reassembly and testing

Small flat washer for KitchenAid stand mixers. Installs between mechanical components to ensure proper spacing. Replace if worn, cracked, or missing.

Threaded nut secures panels, brackets, and internal assemblies in your stand mixer. Replace if missing, stripped, or damaged to restore secure attachment.

This mixing beater is the removable paddle that blends and aerates ingredients for stand mixers, restoring even mixing performance and consistent batter or dough texture. It's a direct-replacement style beater sold as a single piece. What it does

• Scrapes, folds and beats ingredients to help produce uniform batter and dough
• Restores proper mixing when the paddle is worn, bent or missing
• Helps eliminate unevenly mixed or lumpy batters and incomplete ingredient incorporation
• Works as the primary mixing attachment for compatible stand-mixer heads

• Unplug the mixer and follow the OEM attachment/removal procedure before installing
• Align and lock the beater onto the mixer hub until it seats securely
• Inspect for cracks, bends or wear before use; do not use a damaged part
• Clean per the manufacturer's care instructions; avoid high-heat/dishwasher use unless OEM specifies

The 7 Quart Commercial Stainless Steel Dough Hook can knead yeast dough with ease. This KitchenAid Dough Hook fits 7 and 8 Quart models KSM7588, KSM7589, KSM7990, KSM8990, KSMC895, 3KSMC895, 4KSM7990, 5KSM7580, 5KSM7590, 5KSM7990, 5KSMC895, 9KSM7990, 9KSMC895.

Plastic lift arm that raises and lowers the mixing bowl on stand mixers. Replace if cracked, broken, or worn from frequent use and age.

Elliptical wire whip attachment for bowl-lift stand mixers. Replace your worn, bent, or missing whip to restore fluffy whipped cream and egg white preparation.

Fix a mixer that won't engage or slips during operation. This cam restores proper mechanical linkage timing. Straightforward DIY replacement part.

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

Replacement mounting screw for stand mixer panels, brackets, and trim. Secures internal components to keep parts aligned. Replace if missing, stripped, or rusted.

This is a protective bowl guard that attaches to the mixer to shield the mixing bowl during operation. It helps prevent ingredients from splashing out while allowing access for adding items during mixing. Replace this guard if it is cracked, broken, or no longer locks securely into place on the mixer.

Pour shield attachment for stand mixers. Mounts to bowl rim to prevent splatter during mixing. Replace if cracked, broken, or missing for mess-free operation.

Pin guard for stand mixers. Covers and protects the locking pin mechanism. Replace if cracked, broken, or missing to restore proper appearance.

Protective sleeve fits over mixer shafts to reduce wear and maintain alignment. Replace if worn or damaged to restore smooth operation. Verify fit by model.

Replacement mounting screw for stand mixers. Secures panels and components to the chassis. Replace when original fasteners are stripped, missing, or broken.