Parts for Kitchenaid KN15E1XTC0: 03 - Base And Pedestal Unit, Optional Parts

The Foot is an OEM part for Whirlpool stand mixers. This component is designed to provide stability and support to the mixer, ensuring it remains steady during operation. Positioned at the base of the mixer, the foot helps to prevent movement and vibration, which can enhance the efficiency of mixing and protect your countertop from scratches.

Symptoms of a failing Foot include:

• The mixer wobbling or moving excessively during use
• Increased noise or vibration when the mixer is running
• Visible wear, cracks, or deformation of the foot pad
• Scratches or damage to the countertop surface beneath the mixer

Causes of a bad foot can include prolonged use that wears down the material, exposure to heat or kitchen chemicals that degrade the foot, or physical damage from moving or storing the mixer.

This OEM Whirlpool part is also compatible with KitchenAid stand mixers.

This wavy spring washer applies light, consistent preload between mating parts so components stay snug and quiet. It helps control end play and vibration, supporting smoother, more reliable operation of the assembly.

• Applies axial spring tension to take up end play between parts on a shaft or fastener
• Helps resist loosening from vibration and keeps components fitting tightly
• Can address wobble, rattling, or uneven spacing when the original washer is worn or missing
• Maintains proper alignment and feel in the assembly

• Disconnect power and shut off gas/water before servicing; allow hot surfaces to cool
• Note the original stack order and position before removal; replace in the same orientation
• Seat the washer evenly and avoid over-compressing during reassembly
• Verify smooth operation and minimal play after installation

This pivot screw secures a hinge, lever, or linkage to its bracket to create a stable pivot point. Replacing a missing or stripped screw restores proper alignment and smooth movement of the assembly.

• Fastens a pivoting component to its mounting point
• Maintains alignment and smooth, controlled motion at the pivot
• Helps prevent looseness, wobble, or sag at the joint
• Common symptoms include a missing/loose screw, binding movement, rattling, or uneven gaps

• Disconnect power; shut off gas/water if applicable before servicing
• Support the hinged or moving component to remove load from the pivot
• Remove the damaged screw and start the new screw by hand to avoid cross-threading
• Tighten snugly without over-torquing; replace companion bushings or washers if worn

The 4.5 & 5 Quart KitchenAid Coated Flat Head Beater is an OEM part for Whirlpool KitchenAid stand mixers. This flat beater is designed for thorough mixing and blending of ingredients, ensuring consistent results for a variety of recipes.

Over time, the coated flat head beater can become worn or damaged due to regular use or accidental impact. Coating wear, bending, or chipping can compromise its effectiveness and lead to less efficient mixing.

Symptoms of a bad flat head beater include:

• Chipped or peeling coating
• Bending or warping of the beater
• Inefficient or inconsistent mixing
• Noise or scraping during use

This OEM part is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The 4.5 & 5 Quart KitchenAid Dough Hook is an OEM replacement part for  KitchenAid stand mixers. As part of the power knead attachment collection, this dough hook gently kneads and incorporates ingredients when making breads, rolls, pizza dough, and more. 

The curved blades of the hook provide thorough mixing and stretching of gluten strands for developing elasticity in yeasted doughs. Its integrated planetary motion helps eliminate sticking while providing a professional-quality knead. 

Symptoms of a bad dough hook include: 

• Vibration or grinding noises during use
• Inability to properly incorporate or knead ingredients  
• Dough sticking excessively to hook blades
• Visible damage, cracks, or bends in hook tines or housing

The coated Dough Hook fits KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The K45WW 4.5 & 5 Quart Wire Whip is an OEM part for KitchenAid mixers, specifically designed to fit Whirlpool models. This wire whip is used for incorporating air into ingredients, making it ideal for whipping egg whites, cream, and creating fluffy mixtures for recipes.

You should replace this wire whip if it becomes damaged or worn out. Causes of a bad wire whip can include bending or breaking of the wires due to overuse, exposure to heavy or dense mixtures, or corrosion from prolonged exposure to moisture.

Symptoms of a bad wire whip include:

• Inadequate mixing or whipping
• Bent or broken wires
• Poorly aerated mixtures
• Increased mixing time

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Pouring Shield is an OEM part for KitchenAid mixers. This part fits snugly onto the mixing bowl, helping to prevent ingredients from splattering out during mixing. It also features a convenient pour spout that allows for easy addition of ingredients without stopping the mixer.

Causes of a bad pouring shield can include accidental drops or impacts, exposure to high heat, or stress from frequent use.

Symptoms of a bad pouring shield include:

• Difficulty fitting the shield onto the mixing bowl
• Cracks or chips in the plastic
• Ingredients splattering out during mixing
• Difficulty adding ingredients through the pour spout

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory fastener secures appliance panels, brackets, and components. Replacing a missing or worn screw restores a tight, rattle-free fit and helps keep parts aligned as designed for reliable operation. What it does:

• Fastens specified components to maintain alignment and structural integrity
• Helps reduce vibration, noise, and loosening from normal use
• Replace if stripped, corroded, or missing
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power and shut off water or gas before servicing
• Match location and orientation; replace one-for-one with the original
• Start threads by hand to avoid cross-threading; use the correct driver bit and do not overtighten
• Inspect related clips/inserts; replace if damaged to ensure proper retention

Stand mixer Rotor Slicer, Shredder Attachment for KitchenAid Stand Mixer that includes four stainless steel slicing, shredding cones, and instruction booklet. The slicers include course, thick, think and fine shredder to shred vegetables, fruit and nuts. KitchenAid model number RVS-A

This Grease is an OEM component specifically designed for Whirlpool stand mixers.

Causes of needing to replace grease can include wear and tear from heavy or prolonged use over time. Exposure to oil may also degrade its material integrity. Potential issues include material cracking, tearing of the spiral dough hook shape, or detachment from the central axle.

Symptoms of a bad grease include:

• Detachment or separation from the main mixer body
• Abnormal vibrations or noises during use

This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.