Parts for Kitchenaid KSM90: 04 - Base And Pedestal Unit Parts

Replacement mounting screw for stand mixers. Secures panels, brackets, and internal components. Needed when original is missing, stripped, or damaged.

The Cap-Screw is an OEM component specifically designed for Whirlpool mixers. It contains precision mixing mechanisms that allow users to easily and effectively blend, whip, or beat ingredients.

Symptoms of a bad Cap-Screw include:

• Difficulty turning on or selecting speeds
• Excessive noise or vibration during use
• Inconsistent mixing performance
• Leaks into electrical components

Causes of failure can be faulty power switches, worn gears, damaged housing or bowls, or deterioration of internal wiring over time.

This Cap-Screw is also compatible for use with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and select Kenmore.

This lever latch is the replacement latch used to secure and release the appliance door or access panel, restoring proper door engagement and user operation. It fits the OEM latch location and matches the original white/storm-gray finish. What it does:

• Replaces a broken, cracked or worn latch lever that prevents the door from closing or latching securely
• Restores smooth open-and-close action for the affected door or panel
• Prevents rattling or misalignment caused by a damaged latch
• Matches the original finish to maintain the appliance appearance

• One lever latch (white/storm-gray), as shown

• Disconnect power to the appliance before beginning any repair
• Remove the damaged latch and install the replacement using the factory mounting points; fasteners or clips may be required depending on model
• Handle small plastic parts carefully to avoid breakage during installation
• Refer to your model-specific parts diagram or service manual for exact removal and reassembly steps

This latch lever assembly replaces a worn or broken knob lever that operates the appliance latch, restoring secure door or panel movement and reliable engagement. It's a direct-replacement style part used where the latch handle or lever has failed. What it does:

• Replaces a damaged or cracked latch lever that prevents proper door/panel operation
• Provides the mechanical interface for engaging and releasing the latch mechanism
• Helps stop issues like a door that won't latch, catch, or stay closed due to a broken lever
• Restores proper lever travel and tactile feedback when operating the latch

• One latch lever assembly

• Turn off and unplug the appliance before attempting any repair
• Remove the door or access panel to reach the latch area
• Inspect mating latch components and fasteners; replace any damaged hardware

Replaces a cracked, broken, or missing control knob on your stand mixer's speed or lock lever. Restores comfortable grip and clean appearance.

Rubber foot for stand mixers. Installs at the base to provide stability. Replace if worn, cracked, missing, or damaged to prevent mixer movement.

Replacement hinge pin for stand mixer tilt heads. Secures the pivoting head assembly. Install if your original pin is missing, sliding out, or worn.

Fix a stand mixer head that won't lock down or pops up during mixing. This latch spring restores proper head tension for secure operation.

Bowl lift lever latch for stand mixers. Secures the bowl lifting mechanism in place. Replace if broken, cracked, or missing for proper bowl support.

This latch secures the appliance door and helps ensure a proper close for normal operation. It replaces a worn or broken latch to restore reliable door engagement and user safety. What it does:

• Holds the door closed so the appliance can operate as intended
• Replaces a damaged or broken latch that prevents the door from staying shut
• Helps restore proper alignment and engagement of the door mechanism
• Can reduce door rattling or intermittent closing issues

• Latch

• Disconnect power (and gas, if applicable) before starting any repair
• Remove the door or access panel to reach the latch per your model's service instructions
• Compare the new latch to the old part for correct orientation before installation
• Test the door operation after installation to ensure secure engagement

Secures hinge, lever, or linkage to its bracket on your stand mixer. Replace this screw if stripped, missing, or damaged to restore proper alignment.

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

Two pack Lid Covers used with 4.5 and 5 Quart KitchenAid Tilt Head Stand Mixer. The covers are used for variety of situations for example, when you need to keep ingredients in the bowl cold for hours or want to save extra cookie dough. The Lid Covers are dishwasher safe on the top-rack and fit KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB.

Flat beater attachment for stand mixers. Mixes and blends ingredients in the bowl. Replace if coating is worn, peeling, cracked, or damaged.

Replace your cracked, worn, or missing 4.5-quart stainless steel mixing bowl. Fits tilt-head stand mixers with handle for easy pouring and removal.

Dough hook attachment for KitchenAid stand mixers. Kneads bread, pizza, and roll dough. Replace if your original hook is lost, damaged, or missing.

Wire whip attachment for stand mixers incorporates air into ingredients for whipping cream, egg whites, and fluffy mixtures. Replace if bent or corroded.

Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.

Fix a stand mixer head that won't stay locked or tilts during mixing with this head lock assembly. Simple repair restores secure mixing operation.

Fix a stand mixer head that won't stay locked or tilts during mixing with this head lock assembly. Simple repair restores secure mixing operation.