Black Max Log Splitter Parts

This is a genuine carburetor insulator gasket that is designed to fit select models of lawn mowers. The carburetor insulator gasket is responsible for insulating the carburetor to create a strong seal between it and the engine block and insulate it from the excess heat. This gasket is subject to constant pressure and extreme heat, which can cause it to compress, warp, or become otherwise damaged as a result of regular use. Gaskets should be on the routine maintenance schedule and should be inspected every time other repairs are performed. Without functional gaskets, the engine may run poorly or may not run at all. This genuine OEM carburetor gasket is manufactured by MTD. It can be used in select machines from this brand, as well as those from Troy-Bilt, Cub Cadet, HUSKEE, Yard Man, and Yard Machines. There are hundreds of compatible units that take this gasket. The gasket is made of durable composite materials and sold as an individual unit. Hardware and additional components will require another purchase. Be sure to allow the engine to cool and use the appropriate tools for proper installation without damaging the gasket. Always drain the fuel system before working on the carburetor or internal engine components.

This recoil spring and pulley assembly is used in a variety of small gasoline engines that power devices such as mowers, lawn tractors, and log splitters, among other yard and landscaping devices. The assembly works by tightly coiling the spring in the starter housing. When the starter rope is pulled, the tension on the spring is suddenly released, creating a spark that fires the air/fuel mixture. The combustion starts the engine. The constant tightening and releasing of the tension at times will cause wear on the spring, resulting in the need to replace the spring and pulley assembly. To replace the recoil starter assembly, begin by removing the housing. Next, untie or starter rope and check to see if it is frayed and needs to be replaced as well. Remove the old assembly and install the new unit. Remember when re-tensioning the spring to wind the pulley in the opposite direction. Holding the pulley tightly so the spring does not release, attach the cap. Reattach the rope and coil it around the pulley. It is advisable to wear gloves for this task because the pulley and springs have sharp edges. This OEM certified replacement assembly is compatible with Yard-Man, Husky, Cub Cadet, MTD, Yard Machines, and Troy-Bilt yard equipment.

This is a starter recoil assembly. It is used when starting small lawn equipment and other machines. It engages the flywheel. With time and use, any or all of the recoil can wear out or become damaged, including the spring, housing, rope, or pulley. If something is damaged or worn out, the entire starter recoil assembly must be replaced. Signs that the part requires a repair include an engine that won't start or has difficulty engaging.Replacing a starter recoil assembly is easy and can be done in about 15 minutes. A nut driver and screwdriver are required for the repair. Wear gloves. Make sure the equipment is completely cooled before beginning the recoil assembly replacement. After putting tension on the spring and pulley, hold the housing securely to prevent it from releasing.The starter recoil assembly is a genuine OEM-authorized replacement part. It is sold individually. The starter recoil assembly is compatible with MTD, Cub Cadet, Yard Machines, Husky, Yard-Man, and Troy-Bilt brands. It is a complete part that includes the housing, rope, pulley, and recoil spring. It works with small engines, lawnmowers, log splitters, trimmers, and other similar equipment.

A starter handle is a piece that works in combination with several other components to start the engine in numerous machines, including lawn equipment. It works when the user pulls the starter handle grip, attached by a mechanism to the crankshaft. It turns to start the engine. If the starter handle breaks, it will have to be replaced in order to start the machine. Starter handles can become damaged from normal use, misuse, or after an accident.Replacing the starter handle is a simple project. After locating the mechanism it attaches to, typically a sturdy rope or cord, the starter handle should be tied securely to the end of the string. Wear gloves to protect the hands during the process. Test the strength of the attachment before trying to start the machine.This starter handle is a genuine OEM replacement part. It is sold as an individual piece. This starter handle is made of durable, high-quality material. It can be used in devices from MTD, Husky, Troy-Bilt, Yard Machines, and Yard-Man. It is compatible with various lawnmowers, log splitters, trimmers, and other devices with pull start engines.

A carbon canister air filter is an important piece that helps machines operate in accordance with environmental safety standards. This carbon canister air filter is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually. It is designed for use with pieces of outdoor lawn and garden power equipment that have small engines, such as lawn mowers, tillers, string trimmers, edgers, log splitters, and wood chippers. It is compatible with products by brands such as Craftsman, Cub Cadet, MTD, Huskee, and Yard-Man.The carbon canister air filter part is a crucial device that is found in machines with small engines. The air filter is designed to decrease the amount of air pollution that the machine emits. It is serves the important purpose of increasing the machine's fuel efficiency. The carbon canister air filter traps the vapor the machine releases, but rather than letting it escape the fuel tank, it re-routes it back into the engine.The replacement or repair process of the carbon canister air filter should be straightforward, but the user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.

This part can be used to replace a deteriorating or broken throttle linkage spring, which helps to regulate the speed of outdoor power equipment.As throttle linkage springs age they begin to wear out or can easily break. This can cause serious problems with regulating the speed of outdoor power equipment such as lawn mowers and trimmers. A broken or weak throttle linkage spring will stop the throttle on the equipment from returning to the off or resting position when the throttle is released. This can be dangerous. This throttle linkage spring is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement throttle linkage spring fits various different MTD, Cub Cadet, Craftsman, and Troy-Bilt models of lawn mowers, log splitters, and trimmers. Please note that this part is sold individually.

This part is a carburetor stud. A carburetor mixes fuel and air before delivering it to the engine. The carburetor stud, often called carb stud, is used to ensure a tight seal between the carburetor and the intake manifold. It is important that air and other dirt or debris do not enter the engine, and so this seal between the carburetor and the intake manifold is very important.A carburetor stud may need to be replaced if it is stripped or worn. Of course, a new carburetor stud will be needed if it is missing. If the carburetor and the intake manifold do not have a tight seal, it could be possible that new carburetor studs are needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific carburetor stud is compatible with engines, lawnmowers, and log splitters manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.

Lawn equipment and other machines with small gas-powered engines have fuel tanks that require a fuel tank lower grommet to keep the fuel from leaking. This grommet is located near where the fuel filter and neck meet. With use and over time, the fuel tank lower grommet may wear out or get lost. Leaking fuel is a clear indication that there is a problem with the lower fuel tank grommet. If this occurs, the part will have to be replaced to prevent further leakage and device failure.Before replacing a lower fuel tank grommet, empty the fuel tank completely. Wear gloves for protection. Push the replacement part in the hole and turn slightly to push the piece in. If necessary, use a screwdriver to push in to get a secure fit.This fuel tank lower grommet is an authentic OEM part sourced from the manufacturer. The fuel tank lower grommet is compatible with MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt machines. It can be used in various devices, including lawnmowers, log splitters, trimmers, and other engines. It is made of high-quality material and sold as an individual unit.

This spark arrestor is a genuine MTD part. It is a replacement part for lawn mowers, log splitters, and walk-behind mowers. The spark arrestor is an important safety feature, and it is illegal to sell or operate a machine without one.This part arrests or extinguishes sparks that are created by the engine and other components while the mower is in use. It prevents fires, and mowers should never be used without one.This spark arrestor is a genuine OEM part sourced directly from the manufacturer. It is sold individually. It is compatible with machines made by Craftsman, MasterCut, Bolens, Cub Cadet, Husky, MTD, Troy-Bilt, and Yard-Man.

This part can be used to replace a worn or broken front stud to securely attach the shroud and keep it in place.Engine shrouds are critical for ensuring that air is properly circulated around the engine to keep it cool. Without an engine shroud, overheating can occur quickly and cause serious engine damage. This front stud is intended to attach the front of the engine shroud to secure it in place. This starter/shroud front stud is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement starter/shroud front stud fits various different models of MTD, Cub Cadet, Husky, Troy-Bilt, and Yardman outdoor power equipment such as lawnmowers, log splitters, and trimmers. Please note this starter/shroud front stud is sold individually.

This carbon canister filter can be used to replace old filters that are no longer functioning properly. Carbon canister filters need to be replaced regularly in order to ensure outdoor power equipment runs efficiently. Filters are essential for keeping dirt, debris, and harmful materials from ruining an engine. Without carbon canisters, outdoor power equipment can experience decreased fuel efficiency whilst also contaminating the air with more pollutants from the engine. While an engine is running and even after it has been turned off, fuel vapors rise from the fuel tank and pollute the air. Carbon canisters are essential for trapping these vapors and preventing them from being released. Without a clean, well-functioning filter, carbon canisters cannot work efficiently.This carbon canister filter is a genuine replacement part sourced directly from the manufacturer. This replacement carbon canister filter fits various different models of MTD, Cub Cadet, Yardman, Husky, and Troy-Bilt outdoor power equipment such as lawn mowers, log splitters, and trimmers. Please note this cover plate is sold individually.

This crankcase cover gasket can be used as a replacement part for lawnmowers, lawn trimmers, chipper shredders, edgers, tillers, and log splitters. It is the component responsible for sealing the crankcase of the engine and protecting it from accumulating dirt and debris from the outside and from leaking oil from the inside.When damaged, crankcase cover gaskets can hamper their ability to seal the crankcase, thereby letting in dirt and debris or letting out engine oil. Look for cracks, tears, punctures, piercings, or erosion of the metal material. If the crankcase cover gasket is compromised, it must be removed and replaced immediately before the appliance can be used again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This crankcase cover gasket is a genuine OEM part sourced from MTD. It is sold individually. It is compatible with the following brands: MTD, Cub Cadet, Craftsman, and Yard Machines.

This is a muffler gasket that is located between the engine exhaust and the exhaust system in various types of lawn and garden equipment. When the muffler gasket is in good shape, it prevents exhaust from leaking out of the tool. It comes with a substantial amount of flexibility so that it can expand in the presence of heat. The main task of the muffler gasket is to prevent leaking. If the gasket is damaged or broken, the exhaust may leak from the joint.A muffler gasket can fail due to many situations. It can dry out, lose its flexibility, or develop cracks or holes. Sometimes the muffler gasket will chafe and lose its resistance to heat so it dries out. Muffler gaskets can also tear due to the intense vibrations from equipment. The gasket will need to be replaced by taking out the engine and switching the muffler gasket for a new one.This is a genuine OEM replacement muffler gasket that is sourced directly from the manufacturer. It is sold as an individual part. The gasket can be used in lawnmowers, tillers, string trimmers, edgers, log splitters, and wood chippers manufactured by Cub Cadet, Craftsman, and MTD.