Parts for Frigidaire DGT400A1D: 05 - Blower & Heater Housing Components Parts

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This small retainer clip secures trim and components to the appliance chassis, keeping panels and assemblies properly seated for quiet, reliable operation. It's a simple replacement that restores secure fastening where the original clip has broken or worn. What it does

• Holds panels, trim pieces, or small assemblies in place to prevent looseness and rattling
• Replaces a broken, bent, or missing clip that allows parts to shift during use
• Helps maintain proper alignment of adjacent components for smooth operation
• Works where a firm, non-permanent fastener is required

• One retainer clip

• Disconnect power before servicing any appliance to avoid shock or injury
• Access the clip location by removing the appropriate trim or panel per your model's service instructions
• Use needle-nose pliers or a flat screwdriver to remove the old clip and press the new clip into place until it seats securely

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Hex washer head ,10-32 x 0.375. Ground

This lock washer secures fasteners and helps keep appliance panels and components from loosening during normal use, restoring a stable connection and reducing rattles or movement. What it does

• Grips under a screw or bolt to resist loosening from vibration and thermal cycling
• Helps keep panels, brackets, and small components securely fastened
• Commonly used where a screw or bolt must stay tight despite vibration
• Can reduce rattling noises and intermittent loose-part symptoms

• Disconnect power to the appliance before beginning any repair
• Replace with the same type and orientation of washer for proper locking action
• Use appropriately sized screw or bolt; do not mix with mismatched hardware
• Hand-start fasteners, then tighten to snug fit—avoid over-tightening which can deform the washer

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Sound dampening insulation for dryers. Installs inside cabinet to reduce noise and vibration. Replace if torn, missing, or deteriorated over time.

This lock washer secures fasteners and helps keep appliance panels and components from loosening during normal use, restoring a stable connection and reducing rattles or movement. What it does

• Grips under a screw or bolt to resist loosening from vibration and thermal cycling
• Helps keep panels, brackets, and small components securely fastened
• Commonly used where a screw or bolt must stay tight despite vibration
• Can reduce rattling noises and intermittent loose-part symptoms

• Disconnect power to the appliance before beginning any repair
• Replace with the same type and orientation of washer for proper locking action
• Use appropriately sized screw or bolt; do not mix with mismatched hardware
• Hand-start fasteners, then tighten to snug fit—avoid over-tightening which can deform the washer

Sound dampening insulation for dryers. Installs inside cabinet to reduce noise and vibration. Replace if torn, missing, or deteriorated over time.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This lock washer secures fasteners and helps keep appliance panels and components from loosening during normal use, restoring a stable connection and reducing rattles or movement. What it does

• Grips under a screw or bolt to resist loosening from vibration and thermal cycling
• Helps keep panels, brackets, and small components securely fastened
• Commonly used where a screw or bolt must stay tight despite vibration
• Can reduce rattling noises and intermittent loose-part symptoms

• Disconnect power to the appliance before beginning any repair
• Replace with the same type and orientation of washer for proper locking action
• Use appropriately sized screw or bolt; do not mix with mismatched hardware
• Hand-start fasteners, then tighten to snug fit—avoid over-tightening which can deform the washer

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

Sound dampening insulation for dryers. Installs inside cabinet to reduce noise and vibration. Replace if torn, missing, or deteriorated over time.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.