Parts for Briggs & Stratton 21C214-0357-E1: Blower Housing / Shrouds, Flywheel, Rewind Starter Parts

This air cleaner gasket is a genuine Midwest Engine replacement part for appliances that use small engines, such as wood-chippers, snowblowers, leaf blowers, and lawn mowers. The function of an air cleaner gasket is to seal off and protect the engine from the accumulation of dirt, debris, and gunk in the infrastructure.The air cleaner gasket could be subject to damage from overuse or general wear and tear. If the air cleaner gasket is not sealing, thereby preventing the primer bulb from operating as usual and failing to protect the engine from outside dirt and debris, the part should be replaced immediately. The appliance at hand should not be used until the air cleaner gasket has been replaced. Before purchasing a replacement air cleaner gasket, determine whether or not the problem in question is attributable directly to the air cleaner gasket or if the engine is malfunctioning for another reason.This air cleaner gasket is compatible with the following brands: Briggs and Stratton, Simplicity, and Cub Cadet. This part sold individually.

Flange screws have a flange located near the top of the screw, which helps to distribute the connection force over a larger area to reduce potential damage to the machine. It also allows the screws to be used in oversized or irregular holes, and it helps to ensure they stay in place. This flange screw also has a hex top. Screws can last for a long time. However, they may become corroded or worn over time and need to be replaced. They could also become lost and need a replacement. Without all of the screws in the proper places in a machine, it could vibrate too much, which could render it less effective or unsafe to use. The flange screw is a genuine OEM part that can be used with many types of machines including lawn mowers, snowblowers, tillers, pressure washers, leaf blowers, generators, wood chippers, and other small engines. The screws are compatible with Briggs & Stratton, Craftsman, Toro, Cub Cadet, Murray, Lawn-Boy, Snapper, Simplicity, and MTD.

The pawl friction plate on lawn and garden engines is an essential part of the starter assembly that is needed to crank start the machine. It provides power to the starter cup. If the engine on a machine will not start, it could be due to a broken or worn pawl friction plate. Replace the plate immediately to ensure your machine is working properly. This is genuine OEM part is compatible with a range of product types, including lawnmowers, snowblowers, tillers, pressure washers, generators, log splitters, wood chippers, leaf blowers, and chippers. Compatible brands include Briggs & Stratton, Craftsman, Cub Cadet, Lawn-Boy, Snapper, Simplicity, and Toro. The part is sold individually. Keep in mind that this only includes the pawl friction plate. It does not contain the screw or spring, and these will need to be purchased separately.

This durable plastic ratchet pawl is used on select engines that feature what is known as a Susa starter. In this configuration, the ratchet pawl will be responsible for engaging the recoil starting system. Then, the starting system will allow the engine to fire. Over time, the pawl can become worn or damaged due to regular use. If this happens, the recoil can slip and cause difficulties with starting the engine. If the engine isn’t starting or you can hear it slipping when you try to fire it up, a replacement ratchet pawl could be needed. Be sure to allow the engine to cool before replacing any parts or doing any work and always wear gloves. This replacement is a genuine OEM part that includes two ratchet pawls for various Briggs & Stratton engines on small lawn equipment. This part offers compatibility with over 150 engines from Briggs & Stratton, Toro, Lawn-Boy, and Vanguard by Briggs & Stratton.

This is a genuine replacement fuel line for use with Briggs & Stratton engines. This part is responsible for carrying the fuel from the tank to the fuel pump. The fuel line is attached to both the tank and carburetor using special clamps which hold it tight while making a water-tight seal. The clamps are included.The fuel pump is made of high-grade rubber, however, if left out in the weather, it will begin to break down, causing fuel to leak. Exposure to the elements is the most common cause of damage to this part.Replacing the fuel line is simple. Before replacing, ensure the fuel has been removed from the tank, or prepare a container to receive the fuel one the old line is removed from the tank. Using a clamp tool, release the clamp holding the fuel line and slide it from the fuel tank, and then do the same thing on the other end. When installing the new line, slide the clamps onto the line before placing on the mower. Then, using the clamp tool, slide the clamps into place. This fuel line is a genuine OEM replacement part. It is compatible with many Briggs & Stratton models and is sold individually.

This is a replacement screw to secure the pawl friction plate used in many types of lawn and garden equipment. The part is also sometimes called a flange bolt. It is identical to the original screw that came with the machine and will replace a lost or damaged screw. The screws could become damaged due to corrosion or an incident that causes the screw to bend or break. They also serve as replacements in case the screw was lost. Replacing the screw is a simple repair to make. This is an authentic OEM replacement screw that is sold individually. Some buyers might want to have an extra screw on hand. The replacement screw for the pawl friction plate can be used on lawn mowers, snowblowers, tillers, pressure washers, generators, edgers, log splitters, wood chippers, and other small engines. Compatible brands include Briggs & Stratton, Craftsman, Toro, Cub Cadet, Lawn-Boy, Snapper, MTD, and Simplicity.

This replacement friction spring is a genuine OEM part meant for any number of small appliance engines run using a starter rope. This spring absorbs large amounts of kinetic energy that could damage the starter rope pulley system. It helps keep the pulley from being overstretched, which would create enough pressure to break the entire system. This spring sits at the center of the pulley system and creates resistance as the user yanks the starter rope. Friction springs can become worn out after repeated use, especially if a user tends to yank the starter rope quite forcefully. The most obvious sign of a worn of friction spring is if the pulley system lacks any resistance. As the user pulls the cord, they should feel a little pull back, but if the friction spring is worn, there will be much less resistance. Replacing this part is straightforward and will only require a screwdriver. Simply open the pulley system, carefully remove the old spring, and install the new one. This part is compatible with a wide number of appliances from Toro, Vanguard, Briggs & Stratton, and Lawnboy. It comes sourced from the original manufacturer and ships individually.

This replacement part is a switch key. This is a genuine replacement part made by Midwest Engine. This part is commonly found installed within certain lawn mowers and is able to ensure that the user can turn the machine on and off according to the desired settings. A new switch key might be needed if the current one is unable to turn the machine on or off. This can be caused by normal wear and tear over time. If the key is no longer working, it can be due to this part being damaged. This should be a fairly simple repair and should only use common household tools. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

The carburetor primer is a replacement made for use on small engines, such as those found on lawn and garden equipment. When the bulb is pressed, it moves fuel from the tank to the fuel line and into the carburetor. Once the carburetor has been filled with fuel, any extra will go back to the tank through the return line.The carburetor primer bulb is made from plastic and it can start to wear out over time. It could eventually crack, which would require a replacement. If there is any damage to the primer, no matter how small, it should be replaced.The primer is made from high-quality materials and will work with a range of small engines. It is compatible with certain machines from Briggs & Stratton, Toro, and Murray. The primer is sold individually and it is a genuine OEM replacement part sourced from the manufacturer.

This is an OEM replacement part for the recoil pulley and spring assembly, also called the rewind pulley and spring. The recoil starter, which is operated by a rope, will engage the drive cup on the flywheel, which will start the engine when it is pulled. These are commonly found on lawnmowers and similar outdoor equipment. If the rewind begins to bind when pulling the rope, or if it does not rewind easily, it could indicate that a replacement is needed. In addition, if the plastic on the old pulley is worn and cracked, it is a good idea to replace it before it fails entirely. This OEM assembly comes from the manufacturer and includes the pulley and the spring. The pulley is made from plastic, and the spring is metal. The part can be used for a range of machines and brands. The pulley and spring assembly are compatible with lawnmowers, tillers, and other small engines from brands like Craftsman, Briggs & Stratton, Snapper, Lawn-Boy, Toro, and Cub Cadet.

This is an OEM replacement part for the recoil pulley and spring assembly, also called the rewind pulley and spring. The recoil starter, which is operated by a rope, will engage the drive cup on the flywheel, which will start the engine when it is pulled. These are commonly found on lawnmowers and similar outdoor equipment. If the rewind begins to bind when pulling the rope, or if it does not rewind easily, it could indicate that a replacement is needed. In addition, if the plastic on the old pulley is worn and cracked, it is a good idea to replace it before it fails entirely. This OEM assembly comes from the manufacturer and includes the pulley and the spring. The pulley is made from plastic, and the spring is metal. The part can be used for a range of machines and brands. The pulley and spring assembly are compatible with lawnmowers, tillers, and other small engines from brands like Craftsman, Briggs & Stratton, Snapper, Lawn-Boy, Toro, and Cub Cadet.

Flange screws have a flange located near the top of the screw, which helps to distribute the connection force over a larger area to reduce potential damage to the machine. It also allows the screws to be used in oversized or irregular holes, and it helps to ensure they stay in place. This flange screw also has a hex top. Screws can last for a long time. However, they may become corroded or worn over time and need to be replaced. They could also become lost and need a replacement. Without all of the screws in the proper places in a machine, it could vibrate too much, which could render it less effective or unsafe to use. The flange screw is a genuine OEM part that can be used with many types of machines including lawn mowers, snowblowers, tillers, pressure washers, leaf blowers, generators, wood chippers, and other small engines. The screws are compatible with Briggs & Stratton, Craftsman, Toro, Cub Cadet, Murray, Lawn-Boy, Snapper, Simplicity, and MTD.