Parts for Frigidaire CFEF372EB3: 05 - Body Parts

Screw that adjusts and secures the leveling leg to your range base or bracket. Replace if stripped, bent, or missing to restore stable footing and level your appliance.

The Rack is an OEM part for Frigidaire ovens. This rack provides a sturdy and reliable surface for baking and broiling. It's engineered to withstand high temperatures and support heavy dishes, ensuring your culinary creations are cooked evenly and efficiently.

Over time, oven racks can become warped or damaged due to the high heat they're exposed to or from supporting heavy cookware. This can lead to uneven cooking or difficulty sliding the rack in and out of the oven. 

Symptoms of a bad rack include:

• Difficulty sliding the rack in and out of the oven
• Uneven cooking or baking results
• Visible warping or damage
• Difficulty fitting the rack properly inside the oven

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Has three terminals.

Oven light not working or saw a flash near the bulb? This light socket houses the oven bulb and is a straightforward DIY fix in under 30 minutes.

The Light Bulb (40W) is an OEM part for Frigidaire appliances. Specifically designed to fit and function with Frigidaire models, this 40-watt bulb illuminates the interior of your oven, making it easier to check on the progress of your baking or roasti

The Lens is an OEM component for Frigidaire freezers. It acts as a transparent cover and protective barrier for the freezer compartment lights. Crafted for durability and clarity, the lens avoids frost and minimizes condensation while allowing visibili

Rubber bumper cushions oven or range doors to reduce noise and prevent metal contact. Replace if cracked, worn, or missing to restore proper seating.

Fix F1, F3, or F10 error codes and inaccurate oven temperatures with this sensor. Simple DIY replacement takes about 30 minutes with basic tools.

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critica

Broiler not heating or turning red? This broil element restores high-heat broiling. DIY-friendly repair, typically takes 10-15 minutes with basic tools.

If your oven won't heat or bakes unevenly, the bake element may be burned out. This is a simple 5-10 minute repair—just two screws and wire connectors.

Secures cooktop surface elements to your range for stable contact and even heating. Replace if bent or worn to restore proper element positioning.

Mounting plate that secures the oven to the cabinet or wall. Replace this metal support plate if it's bent, rusted, or missing to ensure proper installation.

Adapter assembly for oven vent system. Installs in back wall to align vent components. Replace if cracked, broken, or missing to restore proper fit.

Reinforces and supports oven door glass panels. Replace if original stiffener is bent, cracked, or missing to properly secure glass in the door frame.

Replacement mounting bracket for electric ranges. Secures components in place inside the range. Needed when original bracket is bent, broken, or missing.

This mounting support bracket secures internal appliance components to the cabinet frame for stable operation and alignment. It helps restore proper fit and prevents rattling or movement of attached parts. What it does:

• Provides a stable mounting point for internal assemblies to reduce vibration and noise
• Restores correct alignment of panels or components that fit to the bracket
• Helps prevent parts from shifting during operation, which can cause rubbing or gaps
• Commonly replaced when a bracket is bent, broken, or missing

• One mounting bracket

• Verify bracket orientation and fastener locations before tightening
• Use appropriate hand tools; avoid over-torquing to prevent damage
• Disconnect power and remove any affected panels before beginning work

Secures internal components and panels on your electric range. Replace if missing, broken, or loose to restore proper assembly and structural integrity.

This is an authentic OEM replacement bracket locking screw sourced directly from the manufacturer for use on range tops. The stovetop bracket is attached to the stovetop and the stove body. This locking screw is a fully threaded 2.1-inch screw. If this screw becomes loose or rusted, it should be removed and replaced to ensure the stovetop remains fully seated and in good working condition. If the screw is missing, the stovetop bracket will not be fully functional, and the stovetop could become loose. To start, disconnect the power and gas from the unit before replacing the screw on the bracket. Make certain the stove burners are not hot. Remove the burner grates, burner caps, and control knobs. Lift the range top cover. Locate the mounting bracket on the wall unit. If the screw is in the bracket but has rusted, use a screwdriver to remove the missing screw. Set the nut aside for use on the new screw. Install the new screw and the nut from the last screw. Check the bracket alignment before tightening the screw. Tighten the screw to the nut. Lower the stovetop and reconnect the power and gas. This bracket locking screw is a heavy-duty 2.1-inch silver metal screw. It is designed for use on gas ranges manufactured by Frigidaire, Kenmore, Electrolux, and Crosley.

This replacement frame restores the outer door trim and helps keep the door aligned and sealed for proper operation. A straightforward, OEM-matching part for repairing damaged or bent door trim and improving fit. What it does:

• Provides structural support and alignment for the appliance door or door trim
• Helps maintain a proper seal to reduce drafts and improve cooling performance
• Stops rattling or vibration caused by a warped or damaged frame
• Restores original appearance where the outer trim is dented, cracked, or bent

• Designed to install in place of the original OEM frame; refer to your model-specific service manual for step-by-step instructions
• Disconnect power to the appliance before beginning any repair to avoid electrical shock
• Handle edges carefully to avoid cuts; use proper tools and fasteners as required
• Replace with OEM-specified fasteners for a secure fit

This replacement outer trim frame restores the door opening and cosmetic finish of your appliance, covering and securing edge components for a clean, factory look. It helps prevent gaps and protects inner components from damage. What it does

• Replaces a cracked, bent, or scratched outer frame to restore appearance and proper sealing
• Secures door edges and keeps internal trim and insulation aligned
• Helps reduce air leaks and keeps components protected from spills or impacts
• Fits the original mounting points for a direct-fit replacement when used with compatible models

• One outer trim frame

• Disconnect power to the appliance or unplug before starting any repair
• Use proper tools to remove door panels or trim; keep fasteners for reassembly
• Handle carefully to avoid scratching the new frame or nearby surfaces
• Follow the appliance manufacturer's service instructions for safe, correct installation

A truss-head shoulder screw used where a short, smooth bearing surface and a wide head are needed for pivoting or locating parts. Replaces worn or missing screws to restore proper alignment and movement. What it does:

• Provides a smooth, stepped shaft (shoulder) for parts to pivot or slide on
• Secures components while maintaining precise spacing and alignment
• Stops looseness that can cause rattling, binding, or uneven movement
• Works in assemblies where a wide truss head prevents pull-through

• Use the correct screwdriver or bit to avoid stripping the truss head
• Do not overtighten; torque just enough to secure the part while allowing intended movement
• If working near electrical components, disconnect power to the appliance first

Replacement mounting screw for ovens and ranges. Secures panels, brackets, and components. Order a new screw if yours is stripped, missing, or damaged.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Mounting screw for electric range, oven, or wall oven assembly. Secures internal components and panels. Replace if stripped, missing, or damaged.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.