Parts for Frigidaire PLEW30S3FCA: 03 - Body Parts

Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is the electric heating element located inside the warming drawer of a range. It provides low, steady heat to keep cooked food warm until serving. Replace this element if the warming drawer no longer heats, heats unevenly, or if the element is visibly damaged or burned out.

Range won't heat or overheats? This safety thermostat protects against excessive temperatures. Direct replacement part for reliable operation.

Positions and supports range components to maintain proper alignment. Replace if cracked, broken, or missing to prevent rubbing and ensure panels fit correctly.

This replacement cover restores the appliance's outer housing to protect internal components and maintain a finished appearance. It fits where the original cover was mounted and keeps debris and moisture away from sensitive parts. What it does

• Shields controls and internal components from dust, spills and everyday wear
• Restores a secure, finished look to the appliance exterior
• Helps prevent exposed wiring or parts that can cause shorting or malfunction
• Common symptom: cracked, broken or missing cover that leaves components exposed

• One replacement cover

• Disconnect power before beginning any service
• Remove retaining screws or clips holding the old cover and keep fasteners for reinstallation only if they are in good condition
• Align tabs or screw holes and secure the new cover without over-tightening

This snap bushing is a push-in panel grommet that protects and secures wiring where harnesses pass through metal or plastic panels. It prevents chafing and helps keep wire routing neat for safer operation. What it does:

• Cushions and shields wires from sharp panel edges to reduce abrasion and shorts
• Secures wiring harnesses in place to prevent unwanted movement or snagging
• Provides a finished, vibration-resistant pass-through for electrical leads
• Commonly replaced when the original bushing is cracked, broken, or missing

• One snap bushing

• Disconnect power before servicing electrical components
• Press-fit into the panel hole until the bushing snaps into place; confirm a secure fit
• Replace if brittle, torn, or deformed; do not use a damaged bushing
• Use pliers for removal if needed; avoid forcing or enlarging the hole

This mounting bracket secures internal components or panels to restore proper alignment and reduce noise. It's a simple replacement that helps stop loose or vibrating parts and keeps service panels and assemblies held firmly in place. What it does:

• Provides a secure attachment point for a panel, trim piece or internal assembly
• Prevents rattling or vibration caused by loose hardware
• Restores proper alignment of removable panels and helps maintain component spacing
• Common symptom: loose or shifting panels, rattling during operation, or visible gap at seams

• Disconnect power (unplug unit or switch off circuit) before starting any repair
• Remove access panels as needed to reach the bracket; keep all original fasteners for reinstallation
• Use appropriate hand tools; avoid overtightening screws which can strip threads or deform the bracket
• If the bracket secures electrical components, secure connections before restoring power

Specs: 10-32 X 0.375

Specs: 10-32 X 0.375

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.