Parts for Frigidaire WL24F2WWMB: 02 - Body Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

White exhaust cover for washer dryer combo units. Replaces cracked, discolored, or missing exhaust caps. Installs on the exterior vent outlet.

This part has been discontinued by the manufacturer and is no longer available.

Replacement mounting screw for washers. Secures panels, brackets, or components inside your washer. Order when original screws are stripped or missing.

The hinge grommet provides cushioning and smooth operation where the washer lid connects to the main body. Replace if the lid doesn't close properly, makes grinding noises when opening/closing, or appears loose and wobbly.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

This part has been discontinued by the manufacturer and is no longer available.

Secures the door strike to your washer, keeping the latch aligned for firm closure. Replace if missing, stripped, or corroded to restore reliable latching.

This coupling connects two components together within the range assembly, providing a secure junction for proper operation. It is typically a small connector piece that ensures a tight, leak-free fit between hoses or lines. Replace this coupling if you notice looseness, leaking, or if the original part has cracked or deteriorated over time.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement fastening screw that secures panels, trim, or internal components in your washer. Needed when original is stripped, missing, or damaged.

This screw is a small fastener used to secure appliance components and trim so panels and parts stay in place. It replaces missing or damaged screws to restore secure assembly and reduce rattling or loose pieces. What it does:

• Fastens panels, brackets, trim, and small components to the appliance frame
• Restores secure mounting when original screws are missing, stripped, or damaged
• Helps stop vibration-related noise from loose parts
• Matches the OEM thread and head style for a proper fit when replacing the original screw

• Disconnect power and water before accessing internal panels or electrical areas
• Use the correct driver bit to avoid stripping the screw head
• Do not overtighten — snug until secure to avoid damaging threads or parts
• If replacing multiple screws, verify each screw matches length and head style before installing

Washer dryer combo not heating or stops mid-cycle? A faulty thermal limiter cuts power when temperatures exceed safe limits. Moderate DIY repair.

Door strike plate for washer dryer combo units. Secures the door latch mechanism to the cabinet frame. Replace if cracked, bent, or missing.

This cable tie secures wiring and small hoses inside the appliance to prevent rubbing, snagging, and vibration-related movement. It's a simple replacement part for restoring proper wire routing and keeping components tidy and safe. What it does:

• Holds wiring harnesses and loose cables in place to reduce wear and chafing
• Helps prevent wiring from contacting hot or moving parts
• Reduces noise caused by loose wires or hoses
• Keeps connectors and lines routed for reliable operation

• Disconnect power to the appliance before servicing
• Route wiring as shown in the appliance wiring diagram or photos, then cinch the tie snugly—do not overtighten
• Trim excess tail and ensure the tie does not stress the wire insulation
• Replace any damaged wiring or insulation discovered during installation

This check valve keeps water flowing in one direction through the refrigerator water line to protect the dispenser and ice maker from backflow. It's a small but important valve that helps maintain proper water delivery. What it does

• Allows one-way water flow to the ice maker and dispenser to prevent backflow
• Helps stop drainback that can cause slow fills or air in the water line
• Reduces risk of water running backward into supply when valves cycle
• Commonly replaced when there is intermittent water flow, noise from the valve area, or water delivery problems

• One check valve

• Turn off water supply before removing or installing the valve
• Disconnect power to the appliance if required by your model before working near electrical components
• Inspect fittings and O-rings for damage and replace if needed to ensure a watertight seal
• Tighten connections securely and check for leaks after restoring water and power

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Red adhesive strip for washers. Secures components and panels inside the cabinet. Replace if peeling, missing, or no longer holding parts in place.

Clear adhesive for washers. Secures components and panels during assembly or repair. Replace if original adhesive has degraded, lost bond strength, or worn.