Parts for Kenmore 790.30522802 (79030522802, 790 30522802): Body Parts

This oven rack replaces a worn, bent, or missing rack to restore secure, level support for bakeware and cookware. It gives smooth slide-and-lock support so pans cook evenly and stay stable while you load and remove food. What it does

• Provides a sturdy shelf for cookware and bakeware inside the oven cavity
• Restores proper spacing and airflow for even cooking and browning
• Replaces racks that are bent, warped, rusted, or no longer sliding smoothly
• Helps prevent cookware from tipping or sliding when inserting or removing pans

• One oven rack

• Install by sliding into the oven side rails at the desired height; no tools typically required
• Wear gloves to avoid pinched fingers and allow the oven to cool completely before removing or installing
• Only use racks and accessories rated for your oven's maximum temperature

Oven light not working or saw a flash near the bulb? This light socket houses the oven bulb and is a straightforward DIY fix in under 30 minutes.

The Light Bulb (40W) is an OEM part for Frigidaire appliances. Specifically designed to fit and function with Frigidaire models, this 40-watt bulb illuminates the interior of your oven, making it easier to check on the progress of your baking or roasting without opening the oven door.

Over time, oven light bulbs can burn out or be damaged from high temperatures or accidental bumps during cleaning or cooking. A functioning light bulb is crucial for the optimal operation of your oven, enhancing visibility and improving your cooking experience.

Symptoms of a bad Light Bulb include:

• The oven interior remains dark when the light switch is engaged.
• Flickering light, indicating a loose connection or nearing the end of the bulb's lifespan.
• Completely non-functional light, which can hinder your ability to monitor cooking progress.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Insulation shield that installs at the base of your oven cavity. Replace this guard if cracked, damaged, or missing to maintain proper insulation coverage.

Oven won't reach or hold set temperature? A faulty temperature sensor causes inaccurate heating. This monitor probe ensures consistent cooking results.

Receptacle for electric and gas ranges and wall ovens. Installs as a connector component. Replace if cracked, damaged, or missing to restore proper fit.

Oven trim that finishes the edges around your oven cavity or door. Replace this trim piece if it's cracked, chipped, broken, or missing for a complete look.

Decorative trim piece for wall ovens. Installs around the oven frame to provide a finished look. Replace if cracked, chipped, or missing for appearance.

This is a black lower base trim piece that attaches along the bottom front of the range. It provides a finished appearance and helps cover the gap between the range body and the floor. Replace this trim if it is cracked, warped, discolored, or missing, which can detract from the appliance's appearance and allow debris to accumulate underneath.

Strain relief retainer secures electrical cables at the cooktop connection point. Replace if cracked, broken, or missing to protect wiring integrity.

Rubber bumper that cushions the oven door when closed. Installs on the frame to prevent metal-on-metal contact. Replace if cracked, missing, or worn.

This wiring harness connects the appliance's control components to power and signals, restoring electrical continuity for proper operation. It replaces a damaged or worn cable assembly to help resolve intermittent power or control issues. What it does

• Transfers power and signal connections between the control board and other components
• Replaces frayed, burnt, or broken wires that can cause intermittent operation or failure to start
• Helps eliminate shorts caused by exposed conductors or damaged insulation
• Restores factory routing and connector fit for reliable electrical contact

• One wiring harness assembly as shown

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Compare the harness and connector shapes to the original before installation for correct fit
• Route wiring following original paths and secure with existing clips or ties to prevent chafing

10-24 x 1/2 inch machine screw that secures temperature probe and thermistor brackets to cooktop, oven, and range chassis. Replace if missing or stripped.

Replacement 10-24 x 3/8 machine screw secures panels, brackets, and trim in ranges and ovens. Replace missing, stripped, or damaged screws.

Mounting screw for electric range and wall oven assembly. Secures internal components and panels. Replace if stripped, missing, or damaged during repair.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation