Parts for Kenmore 790.60712901 (79060712901, 790 60712901): Body Parts

Side panel for gas ranges. Replaces cracked, dented, or damaged exterior panels. Restores the structural integrity and appearance of your range.

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Leveling leg assembly installs at the front corners of your range. Replace if broken, rusted, missing, or no longer adjusts to level your appliance.

Replace your cracked, warped, or hard-to-clean oven rack. This durable rack installs inside your range oven to support cookware during baking and roasting.

This metal panel forms the bottom surface of your gas oven cavity. It protects the oven interior and helps distribute heat evenly during cooking. Replace it if you see rust, warping, or holes in your oven bottom that affect heating performance.

Secures panels and components in your range or oven. Replace if broken, bent, or missing to prevent shifting and reduce vibration noise. Confirm fit.

Replace your gas range flue gasket to seal the flue opening and prevent heat loss. Install when worn, cracked, or damaged. Confirm fit with model number.

Directs exhaust and heat from the oven cavity to the range vent path. Replace this flue if yours is damaged, corroded, or missing for proper ventilation.

This is the right side cover. For left side use 316233500.

This is the left side cover. For right side use 316233400.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.

Fiberglass insulation panel that installs behind the oven cavity. Replaces missing, damaged, or rodent-chewed insulation to restore heat containment.

Metal shield that protects the oven ignitor assembly from spills, drips, and debris. Replace if cracked, bent, damaged, or missing to restore protection.

Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.

Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.

This main wiring harness connects a refrigerator's control board and key components, providing organized power and signal routing so controls, lights and the compressor operate reliably. Replaces a damaged or burned main harness for restored electrical continuity. What it does

• Routes power and signal connections between the control board, lights, compressor and sensors.
• Prevents intermittent operation caused by loose, corroded or broken wiring.
• Can stop failures such as no lights, components not running, or control errors when the harness is the fault.
• Keeps wires organized and secured to avoid chafing and shorting.

• One main wiring harness as pictured.

• Disconnect power before servicing to prevent shock or damage.
• Compare the new harness to the original and route wires the same way; replace any damaged clips or grommets.
• Reconnect all terminals fully; loose connectors can cause intermittent faults.

Size: 8-18ab x 0.5 inch.

Support plate that mounts to the bottom of your range oven cavity. Replace if the original plate is cracked, warped, or damaged from heat exposure.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Size: 8-32t x 0.500 inch. Color: Black.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.