Parts for Tappan TEF303BWD: 05 - Body Parts

This burner box is the steel housing that supports and protects the gas valves, burners and internal gas components in a gas range. It restores proper alignment and containment for safe, efficient burner operation. What it does:

• Houses and secures the range's gas valves, burners and related internal parts
• Directs and contains gas flow and flame components for reliable ignition
• Helps prevent gas or flame exposure to surrounding cabinet areas
• Commonly replaced when the original box is dented, damaged, corroded or interfering with burner alignment

• Replace only after disconnecting gas and power; follow appliance shut-off procedures
• Inspect related seals, gaskets, valves and fasteners during installation; replace as needed
• Use common hand tools; avoid bending or distorting the box during fitment

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

Leveling leg assembly installs at the front corners of your range. Replace if broken, rusted, missing, or no longer adjusts to level your appliance.

Replace your cracked, warped, or hard-to-clean oven rack. This durable rack installs inside your range oven to support cookware during baking and roasting.

Replacement refrigerator door hinge that supports proper door alignment and smooth opening and closing. Restores secure door operation to prevent sagging, binding or air leaks when a hinge is worn or damaged.

• Supports and pivots the refrigerator door for stable, reliable opening and closing.
• Maintains door alignment to reduce gaps that can cause cold air loss and temperature issues.
• Designed to match factory fit and function for the door hinge mechanism.

• Disconnect power and remove food from the door before starting to reduce risk of injury or damage.
• Support the door while removing and installing the hinge to prevent it from falling or bending.
• Retain original mounting hardware; use the correct screws and torque values per the service manual.

The Broiler Pan Assembly is an OEM part for Frigidaire ranges and ovens. This part includes both the broiler pan and the grill rack, designed to catch drippings and promote even cooking when broiling foods.  This assembly includes pan and insert.

Causes of a bad broiler pan assembly can include wear and tear from regular use, warping or rusting due to high temperatures, or damage from improper cleaning methods.  

Symptoms of a bad Broiler Pan Assembly include:

• Visible warping or rust on the pan or rack
• Difficulty in cleaning due to persistent stains or damage
• Uneven cooking results when broiling
• The pan or rack no longer fitting securely in the oven

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Broiler Pan Assembly is an OEM part for Frigidaire ranges and ovens. This part includes both the broiler pan and the grill rack, designed to catch drippings and promote even cooking when broiling foods.  This assembly includes pan and insert.

Causes of a bad broiler pan assembly can include wear and tear from regular use, warping or rusting due to high temperatures, or damage from improper cleaning methods.  

Symptoms of a bad Broiler Pan Assembly include:

• Visible warping or rust on the pan or rack
• Difficulty in cleaning due to persistent stains or damage
• Uneven cooking results when broiling
• The pan or rack no longer fitting securely in the oven

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Secures range trim, panels, and components to prevent rattles and loosening. Replace when clips break or lose tension. Confirm fit with your model number.

Secures panels and components in your range or oven. Replace if broken, bent, or missing to prevent shifting and reduce vibration noise. Confirm fit.

This is the right side cover. For left side use 316233500.

This is the left side cover. For right side use 316233400.

Replacement access cover kit for electric ranges. Covers internal components and wiring. Order a new kit if your original is cracked, broken, or missing.

Insulation wrap that surrounds the oven cavity to retain heat and protect outer panels. Replace if damaged, torn, or missing to restore heat retention.

Fiberglass insulation panel that installs behind the oven cavity. Replaces missing, damaged, or rodent-chewed insulation to restore heat containment.

Insulation blanket surrounds the oven cavity to retain heat. Replace if burnt, deteriorated, or damaged by pests to restore proper heat retention.

Replace your range's oven vent tube if it's cracked, damaged, or missing. This duct channels hot air and steam from the oven cavity to the exhaust system.

If your range has no power or burnt plastic smell, the terminal block may be melted. This kit restores secure power connections. Moderate DIY repair.

Stop rattling and loose panels in your range with this support plate. Secures internal components, reduces vibration, and restores proper alignment.

Oven won't broil or heats unevenly? The broil element provides high heat from above for browning. DIY-friendly repair, usually takes 10 minutes to replace.

Oven won't heat or bake properly? This bottom bake element converts electricity to heat for even baking. Simple DIY fix—2 screws, 2 wire terminals.

Support bracket that secures the broil heating element in your range oven. Replace if cracked, broken, or missing to properly mount the broiler element.

Insulation shield for electric ranges. Installs to protect internal components from heat. Replace if cracked, damaged, or missing for proper insulation.

Mounting plate for electric and gas ranges. Secures components in place. Replace if cracked, bent, or broken to restore proper structural support.

Anti-tip bracket kit secures your range to the floor or wall, preventing tipping when the oven door is opened or heavy cookware is placed on extended racks.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Push-in plug button that covers openings in the oven bottom panel. Replace if cracked, missing, or broken to keep debris out and maintain a clean finish.

Size: 8-18ab x 0.5 inch.

Hex flange nut with 10-32 thread secures components in appliances. Replace if stripped, missing, or damaged. Flange provides broader bearing surface.

Size: 10-32 x 0.312 inch. Color: Black.

Size: 6-20 x 0.312 inch.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Size: 8-32t x 0.500 inch. Color: Black.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.