Bolens Log Splitter Parts

Flange bearing for lawn tractors and walk-behind mowers. Replace when you notice excessive noise, wobbling, or difficulty with blade rotation. Verify fit with your model number before ordering.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

Engine won't start after sudden stop? A sheared flywheel key breaks the connection between crankshaft and flywheel. Simple DIY repair.

This push rod kit is a genuine MTD part, sold individually. This push rod kit can be used as a replacement part in a lawnmower. This kit comes with a variety of push rods in various shapes and sizes, perfect for the replacement or repair of a push rod within the internal machinery of the lawnmower. The push rods could be dented, punctured, scraped, cracked, warped, or eroded, and if this occurs to the point of reduced or no efficacy, the push rod kit should be ordered as a genuine OEM replacement part.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This push rod kit is compatible with the following outdoor appliance brands: MTD, Bolens, Yard-Man, Yard Machines, Troy-Bilt, Cub Cadet, and Husky.

Rope won't retract or gets stuck when pulling? This recoil starter spring restores smooth pull-and-retract action on walk-behind mowers and tillers.

Fuel line kit for lawn mowers. Connects fuel tank to carburetor. Replace if cracked, dry-rotted, leaking, or hardened to restore proper fuel flow.

Replacement ignition coil for outdoor power equipment engines. Installs on the engine block. Replace if cracked, corroded, or missing for proper ignition.

Engine won't start or pull cord slips? This starter cup connects the recoil mechanism to start your engine. Simple bolt-on replacement part.

Fix engine overheating issues with this cooling fan. Keeps your small engine running at proper temperature. Direct replacement part for reliable operation.

Oil fill plug assembly for small engines. Seals the oil fill opening to prevent leaks. Replace if cracked, stripped, or missing to maintain proper seal.

Engine running rough or hard to start? A worn carburetor insulator allows air leaks that disrupt fuel mixture. Simple DIY fix restores smooth operation.

Seals and insulates the carburetor from engine heat on lawn mowers and outdoor power equipment. Replace if cracked, worn, or causing air leaks.

Carburetor gasket seals fuel and air mixture, preventing leaks. Replace when you notice fuel odors, poor performance, or during carburetor service.

This is an authentic OEM replacement part sourced directly from the manufacturer for use in various small engines. This oil fill tube assembly is part of the oil delivery system. This tube delivers the oil to the oil tank when it is added to the engine. If this tube cracks or deteriorates over time, the oil will not make it to the oil tank or the engine. This could lead to complete engine failure if the leak is not discovered. Oil on the driveway or lawn or smoke coming from under the engine when the lawnmower is running is a sure sign that the tube may need to be replaced.The oil fill tube assembly also houses the dipstick which is used to check the oil level in the mower. If the assembly is leaking, the reading won't be accurate and the lawnmower may be operated without adequate oil which can damage the engine. A screwdriver is needed to replace the oil fill tube. Do not replace this part until the engine has cooled. This oil fill tube assembly is made of black molded plastic and sold as an individual unit. It is designed for use in lawnmowers and other small engines manufactured by Toro, Tecumseh, and Briggs & Stratton.