Bosch Cooktop Parts

This door seal restores a tight barrier between the oven door and cavity. Replacing a worn gasket helps your oven reach and hold temperature, reduces heat escaping at the door edges, and supports more consistent baking and roasting results.

• Creates a heat-resistant seal around the oven opening
• Helps the oven preheat and maintain set temperature
• Limits heat, steam, and odors from escaping at the door
• Typical signs it needs replacement: visible tears or flattening, heat felt around the door, longer preheat/cook times, or uneven baking

• Disconnect power at the breaker and let the oven cool completely
• Open the door, pull the old seal from its channel, and clean the groove
• Press the new seal evenly into the channel without stretching; ensure corners seat fully
• Close the door to verify uniform contact all around and adjust as needed

The Fan is an OEM component specifically designed for select Bosch built-in ovens. As a critical convection element, it circulates internal air currents for optimal heat distribution throughout baking and broiling cycles.

Powerful yet precisely balanced centrifugal motion agitates spacious oven cavities with homogeneous warmth. Aerodynamic fan blades expedite even cooking without hot or cold spots. 

Causes requiring replacement relate to bearing seizure or broken blade attachments disrupting designed circulation. Prolonged heat exposure may cause premature motor failure or cracked housings to no longer sustain needed speeds.

Symptoms signaling the need for a new fan include:

• Inability to effectively circulate air for simultaneous multi-rack cooking  
• Louder than average operation noise accompanied by vibration
• Erratic or ineffective temperature management within cycles

This OEM Bosch replacement fan is also compatible with Thermador, Gaggenau, and some Kenmore built-in ovens employing convection methods. Proper reinstallation restores designed air transfer capabilities for perfect results.
 

The Hook is an OEM part for Bosch microwave doors. Manufactured from heat resistant composite materials, it firmly holds the door closed during cooking cycles.  

Causes of a faulty latch/hook include failures of being worn down from repetitive opening/closing motions over time. Exposure to high heat or abrasive cleaners also leads to decreased functionality.

Symptoms of a damaged latch/hook involve:

• Doors not sealing fully or locking properly
• Failure to open after cooking
• Degrading latch fittings allowing moisture or debris entry

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Ignition Device is an OEM component specifically designed for Bosch gas ranges. This device is responsible for generating the spark needed to reliably light the burners on the cooktop.

Symptoms of a faulty ignition device include:

• Inconsistent or intermittent burner ignition  
• Small flames that do not spread fully across burners
• Complete failure of one or more burners to light
• Burners extinguishing unexpectedly during use

Causes of ignition device problems tend to be worn over time from repeated use. Exposure to moisture, residue buildup, or physical impacts can also potentially damage sensitive electronic components. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore gas ranges and cooktops.

This Venturi is an OEM part for Bosch Ranges. It plays a role in supplying air to the burner for proper combustion. Continuous exposure to heat and debris can cause this part to degrade or malfunction.

What Causes a Bad Venturi: 
Exposure to heat and debris from cooking can cause the venturi to deteriorate over time. Blockages or clogs in the venturi can also affect its functionality.

Symptoms of a Bad Venturi:

• Uneven flame or inconsistent burner operation
• Reduced gas flow to the burner
• Burner flame discoloration

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Burner Cap is an OEM part for Bosch gas cooktops. This small black burner cap safely contains the flame underneath to concentrate heat efficiently for precise cooktop control. Reliable burner caps are crucial for safety, performance, and aesthetics.

Causes of a bad burner cap can include warping or cracking from continuous exposure to high heat over the long run, as well as surface scratching or punctures.

Symptoms of a faulty cap include:

• Flames escaping beyond cap and licking up sides of cookware
• Visible damage or deterioration on cap surfaces
• Inability to adjust flame height as intended
• Burners no longer heating or shutting off properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Knob is an OEM component specifically designed for select Bosch gas cooktops. As the physical interface, it facilitates intuitive burner selection and precise flame level adjustment.

Durable polymer construction and tight mechanical tolerances withstand frequent adjustments without loosening or degrading. Ergonomic profiling allows natural operation even with pot handles obstructing access.

Causes requiring knob replacement usually relate to stripped or worn-down cams and gears from heavy usage. Over-tightening during cleaning could also permanently damage internal components. 

Symptoms signaling the need for a new knob include:

• Loose, wobbly, or difficult adjustment movements between settings  
• Knob rotation failing to properly engage control valves
• Stripped identification markings blurring burner association

This OEM Bosch replacement knob is also compatible with Thermador, Gaggenau, and selected Kenmore gas cooktops utilizing identical valve actuation mechanisms. Reinstallation preserves the intended control function.
 

The Knob Set is an OEM part for Bosch cooktops. This set includes four burner knobs designed to control the heat settings of your cooktop burners. The knobs allow you to easily identify and adjust the desired heat level for each burner.

A bad burner knob can occur due to accidental damage, wear and tear over time, or improper handling. Signs of a faulty knob include cracks, loose or wobbly fit, or difficulty in turning the knob smoothly.

Symptoms of a bad knob include:

• Cracks or visible damage 
• Loose or wobbly fit 
• Difficulty in turning the knob 

Replace your worn-out or damaged knobs with this genuine OEM Bosch part to restore your cooktop. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

The Jet Holder with Nut is an OEM part for Bosch ranges and cooktops. It holds precisely machined jets that control gas flow from each burner valve.

Causes may be wear and deterioration from prolonged heating exposure. Physical impacts or damage accumulation over time could also compromise the jet holder.

Symptoms of a bad jet holder can include:

• Inability to adjust or maintain proper flame stability and heat output
• Irregular or uneven flame patterns between surface burners
• Potential gas leaks observed at jet connections

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Cooktop Bracket Kit is an OEM part for Bosch cooktops. This bracket and hardware kit serves to securely fasten the cooktop surface to the underlying countertop.

Causes of a bad bracket can include wear and deformation from heavy cooktop use over time, or damage to fastening screws from accidental impacts.

Symptoms of a bad bracket and fastening kit include:

• The cooktop surface becoming loose, wobbly, or unstable during use
• Gaps appearing between the cooktop and countertop edges
• Reduced heat containment and risk of burns from loose surfaces

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This includes one single foot. For the four pack order part number 00413552

The Burner Cap Assembly "C" Matte Blk is an OEM part for Bosch gas cooktops. As the rounded covering fitted over individual burners, it safely contains flames underneath cookware. Maintaining proper cap placement is vital for heating performance and safety compliance standards.

Causes of a bad burner cap assembly can include cracks or punctures from sustained high temperature cycling that compromise its insulating barrier. Over time, surface imperfections like scratches also diminish durability against consistent heat exposure.

Symptoms of faulty caps are:

• Flames improperly escaping from under pan edges
• Visible damage present on cap surfaces
• Inconsistent flame height adjustment or shut-off
• Excessive heat concentration in burnered area

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This grate foot assembly installs on the underside of a gas cooktop or range grate to cushion and stabilize it. Replacing worn or missing feet helps protect the surface and keeps cookware level while you cook.

• Cushions contact between the grate and cooktop surface
• Helps keep the grate from sliding and reduces rattling
• Maintains proper grate height for stable, level cookware
• Common symptoms: wobbling/rocking grate, missing or hardened feet, scratches on the surface

• Allow the cooktop and grates to cool completely before servicing
• Remove the grate, pull off the old foot, and clean the mounting area
• Press the new foot firmly into place; if your model uses an adhesive or retainer, follow the manufacturer's cure time before using the burners
• For best results, replace all feet on a grate at the same time and it sits flat

This oven control knob lets you select temperatures and cooking functions with a smooth, precise turn. It restores easy, accurate control when the original knob is worn, cracked, or missing, keeping your range looking and working its best.

• Turns the oven's selector/temperature shaft to choose settings
• Replaces knobs that are loose, broken, stripped, or missing
• Helps resolve issues like slipping when turned or inability to select temperatures
• Maintains a clean, factory look with a stainless-style finish

• Disconnect power and allow the appliance to cool before servicing
• Pull the old knob straight off the control shaft; avoid prying against the panel
• Align the knob's flat/D-shaped insert with the shaft and press firmly until seated
• Test for smooth rotation and proper engagement of oven functions

Control knob that restores tactile control over a burner or temperature selector, giving a positive grip for accurate setting. Installs in place of a cracked, stripped, or missing original knob. What it does:

• Provides a comfortable grip to turn a range/oven or cooktop control for selecting heat or function.
• Replaces knobs that are cracked, loose, stripped, or won't stay on the control shaft.
• Engages the control shaft to transmit user input to the valve or selector.
• Matches the OEM fit and appearance for a factory-like replacement.

• Always disconnect power (and gas where applicable) and allow the appliance to cool before servicing.
• Pull the old knob straight off the shaft; align and push the new knob onto the control shaft until fully seated.
• Do not force a knob onto a shaft—forcing can damage the control or the new part.

This door opening lever is the replacement release lever that lets the appliance door latch open and close smoothly, restoring reliable door-opening action and making everyday use easier. What it does:

• Replaces a worn, broken, or cracked lever that releases the door latch.
• Lets the door latch release properly so the door opens without excessive force or sticking.
• Works with the latch assembly to help ensure the door closes securely and operates smoothly.
• Addresses common symptoms such as a loose or unresponsive door handle, difficulty opening the door, or a lever that snaps.

• Disconnect power (and water, if applicable) before attempting any repair.
• Access may require removing the door trim or outer panel; basic hand tools are typically needed.
• Inspect surrounding latch components while replacing the lever and replace any damaged hardware.