Bosch Cooktop Parts

Secures the burner orifice in position to deliver the correct gas jet size for your 12,500 BTU natural gas burner. Replace if cracked, broken, or missing.

Supports the burner assembly and positions the cap for consistent flame distribution. Replace if damaged, warped, or causing burner misalignment.

Pressure regulator for gas cooktops maintains consistent gas flow to burners. Replace if leaking gas odor, damaged vent, or worn seals detected.

This burner base supports the cooktop's burner cap and directs flame for even heating. It replaces a damaged or warped base to restore stable burner alignment and consistent flame pattern. What it does:

• Holds the burner cap in place and centers the gas flame
• Channels gas flow for proper burner operation
• Helps prevent wobbling or uneven heating from a warped base
• Commonly replaced when the base is cracked, corroded, or bent

• One burner base (B)

• Turn off gas supply and power to the appliance before servicing
• Remove surrounding burner components and reassemble in reverse order
• Inspect nearby seals and burner ports for damage; replace if necessary

This replacement circulation pump motor restores water movement inside the dishwasher so wash performance and draining return to normal. It directly drives the pump impeller to move water during wash and rinse cycles. What it does:

• Spins the pump impeller to circulate and move wash water for effective cleaning
• Stops circulation when failed, which can cause poor cleaning or incomplete cycles
• May produce unusual grinding or whining noises when worn
• Can trigger circulation or pump-related error codes on some models

• Always disconnect power before beginning service
• Access may require removing the lower access panel and/or pump housing; keep track of fasteners and seals
• Reuse existing mounting hardware and gaskets unless damaged; replace seals if leaking

This replacement cooking-area knob restores user control to a range or cooktop, providing a secure grip and clear position changes for accurate heat selection. Durable plastic construction matches original fit and feel. What it does:

• Replaces a worn, cracked, or missing cooking-area control knob so temperature settings can be selected reliably
• Engages the stove's control shaft to turn burners or elements on and off
• Helps prevent accidental slips or mis-selections with a firm, indexed grip
• Common symptom fix: knob won't turn, is loose, or stops responding

• One replacement cooking-area control knob

• Turn power/gas to the appliance off and allow surfaces to cool before servicing
• Pull the old knob straight off the control shaft and push the new knob fully onto the shaft until seated
• If knob does not seat, verify shaft type and knob orientation; do not force to avoid damage

Replace worn cooktop burner gasket seals to prevent gas leaks and ensure proper flame control. Verify compatibility with your model number before ordering.

Secures 6mm shafts and spindles on cooktop burners and controls. Replace if parts slip or wobble during use. Confirm 6mm shaft size before ordering.

This door latch assembly secures the door closed and signals the control that it's safely shut, allowing cycles to start and run. Replacing a worn latch restores a reliable safety interlock and consistent operation.

• Secures the door and engages the safety interlock so the appliance can operate
• Sends a "door closed" signal to the control
• Common symptoms: door won't latch or stay closed; unit won't start or pauses as if the door is open; intermittent operation when the door is bumped; visible wear or damage to the latch
• Helps prevent nuisance "door open" indications

• Disconnect power before servicing
• Access the latch from the door area; remove inner panel or trim as required by your model
• Note wire positions, transfer connectors, and mount the new latch in the same orientation
• Test door closure before reassembly

Microwave door won't close or latch properly? This door latch assembly secures the door during operation, allowing cycles to start and run safely.

Used to hold down the jet holder assembly.

Fix uneven baking or slow preheating in your wall oven. This convection fan motor restores proper air circulation for consistent cooking results.

The Knob Set is an OEM part for Bosch cooktops. This set includes four burner knobs designed to control the heat settings of your cooktop burners. The knobs allow you to easily identify and adjust the desired heat level for each burner.

A bad burner knob can occur due to accidental damage, wear and tear over time, or improper handling. Signs of a faulty knob include cracks, loose or wobbly fit, or difficulty in turning the knob smoothly.

Symptoms of a bad knob include:

• Cracks or visible damage 
• Loose or wobbly fit 
• Difficulty in turning the knob 

Replace your worn-out or damaged knobs with this genuine OEM Bosch part to restore your cooktop. This Bosch part can also be used on Thermador and Gaggenau appliances.
 

M4 rubber gasket creates watertight seal and reduces vibration around fasteners. Replace when worn, cracked, or leaking. Verify fit with your model number.

Gas pressure regulator for ranges and cooktops. Controls fuel flow to burners. Replace if leaking, cracked, or damaged to restore proper gas delivery.

This replacement cooktop knob restores smooth heat control and a clean, finished look. It includes a trim ring and installs by pressing onto the control stem. What it does:

• Mounts to the control stem to turn the burner/element on and off and adjust heat level
• Replaces a broken, stripped, or missing knob
• Helps when the knob slips, won't turn, or won't stay seated
• Refreshes the appearance of the control panel

• Ensure the cooktop is off and completely cool.
• Pull the old knob straight off; remove the old trim ring if present.
• Position the new trim ring over the opening.
• Align the knob with the stem and press straight on until fully seated—do not force or use tools on the stem.