Bosch Washer Gasket & Seal

The Door Seal, Light Gray is an OEM part for Bosch washing machines. This part ensures a water-tight seal between the door and the machine's body. This part prevents water leaks during the washing cycle, thereby protecting your floors from damage and ensuring that the washing process is both efficient and safe.  

Causes for issues with the door seal often involve regular wear and tear from use, exposure to harsh cleaning chemicals that can degrade the rubber, or physical damage from loading and unloading clothes.

Symptoms of a malfunctioning Door Seal include:

• Visible wear, tears, or cracks in the seal
• Water leaking from the front of the washing machine during operation
• A buildup of mold or mildew on the seal, contributing to bad odors

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This water inlet hose gasket seals the connection between the supply hose and the appliance's inlet fitting. Replace a flattened or damaged washer to stop drips at the coupling and restore a reliable, watertight connection.

• Creates a watertight seal at the inlet hose-to-appliance connection
• Helps prevent drips, puddles, and water damage around the machine
• Replace if the old gasket is cracked, hardened, flattened, or missing
• Common symptoms: leaking at the hose coupling or needing to retighten the fitting to stop drips

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water, then detach the inlet hose from the appliance fitting
• Remove the old gasket from the hose coupling and seat the new gasket evenly
• Reattach and hand-tighten the coupling; open water supply and check for leaks—do not overtighten

A flat seal ring that forms a watertight gasket for pumps and valves, helping prevent leaks and maintain proper water flow in appliance wet systems. Replaces worn or damaged rings to restore reliable sealing. What it does:

• Creates a tight seal between mating metal/plastic parts to stop water leaks
• Keeps pump housings and valve connections watertight under normal operating pressure
• Helps maintain correct water flow by preventing bypass around seals
• Commonly replaced when brittle, cracked, or deformed from wear or heat exposure

• Disconnect power and shut off water supply before starting any repair
• Inspect mating surfaces for damage or debris and clean before installing new ring
• Seat the ring evenly without twisting or over-stretching to avoid leaks

The door boot gasket is the flexible rubber seal between the washer's front tub and the door opening. It keeps wash water contained during cycles and helps prevent drips and leaks at the front of the machine. What it does

• Forms a watertight seal between the outer tub and the door opening
• Helps prevent leaks and water on the floor during and after cycles
• Restores proper sealing when the original gasket is torn, deformed, or moldy
• Common symptoms: water leaking from the door, visible rips, musty odors, or a door that won't seal properly

• Includes: 1 door boot gasket

• Unplug the washer and turn off both water supplies before servicing
• Remove the outer retaining band/clamp and release the old gasket from the front panel
• Access and remove the inner clamp; note gasket orientation, then remove the old gasket from the tub lip
• Fit the new gasket fully onto the tub, reinstall inner and outer clamps, and test for leaks before reassembly

This O-ring is a small rubber seal that prevents water leaks by sealing a connection point inside your appliance. It's a simple, inexpensive part that restores a watertight joint when the original O-ring is worn or damaged. What it does:

• Seals mating surfaces to stop or prevent water leaks at fittings and connections
• Maintains pressure integrity in fluid pathways
• Replaces cracked, flattened, or hardened O-rings that allow dripping or seepage
• Helps restore normal operation by re-establishing proper sealing where the original failed

• Disconnect power and shut off the water supply before replacing any seals
• Remove the damaged O-ring and clean mating surfaces; ensure the replacement seats evenly
• Inspect surrounding parts for damage; replace additional worn components as needed
• Do not stretch or nick the O-ring during installation; use the correct size for a proper seal