Parts for Maytag MEDB955FC2: Bulkhead Parts

The Front Drum Roller Shaft is an OEM part for Whirlpool dryers. This component provides support and stability to the drum while it rotates, ensuring smooth and quiet operation during the drying cycle. The roller shaft works in conjunction with the drum rollers to maintain proper alignment and reduce friction.

Over time, the front drum roller shaft can wear out or become damaged due to continuous use and the constant movement of the drum. Factors such as heavy loads, misalignment, and lack of lubrication can contribute to the deterioration of the shaft.

Symptoms of a bad front drum roller shaft include:

• Squeaking or grinding noises during the drying cycle
• The drum not rotating smoothly
• Increased friction or resistance when turning the drum by hand
• Uneven or excessive wear on the drum rollers

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This factory fastener secures appliance components and panels, helping keep assemblies properly aligned and tight. Replace worn, stripped, or missing hardware to eliminate looseness and vibration and maintain safe, reliable operation.

• Fastens brackets, panels, trim, and internal assemblies to the cabinet/frame
• Helps maintain alignment of doors, consoles, or covers
• Restores a tight fit to reduce rattling, vibration, or shifting
• Common symptoms: missing screw, stripped head/threads, loose panel or handle, recurring vibration/noise

• Disconnect power (and shut off gas/water if applicable) before servicing
• Match thread and length to the original fastener for proper fit
• Start threading by hand to avoid cross-threading; use the correct driver
• Do not overtighten into plastic or thin sheet metal

The Dryer Thermostat is an OEM part for Whirlpool dryers. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.

You should replace this dryer thermostat if it becomes faulty. Common causes of a bad dryer thermostat include electrical failures, buildup of lint or debris causing overheating, and general wear and tear over time.

Symptoms of a bad dryer thermostat include:

• Dryer overheating or not heating at all
• Extended drying times
• Dryer shutting off prematurely
• Error codes related to temperature control

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement air duct channels and directs airflow inside the appliance to help maintain balanced temperatures. Replacing a cracked, warped, or missing duct restores proper air circulation and helps the unit cool more consistently. What it does

• Routes air through internal passages between compartments
• Helps maintain consistent temperatures by preventing leaks and bypasses
• Restores designed airflow when the original duct is damaged or missing
• Common symptoms include uneven cooling, warm spots, frost or moisture buildup, or unusual airflow noise

• 1 air duct

• Disconnect power before servicing; wear cut-resistant gloves around sharp panels
• Remove shelves/panels as needed to access the duct and retain all fasteners
• Transfer any foam seals or gaskets from the original part
• Ensure the duct seats fully and fasteners are snug to prevent air leaks

A duct collar that connects and secures the dryer's exhaust duct to the appliance, helping channel hot, moist air safely out of the dryer. Replaces a damaged or loose collar to restore a tight vent connection. What it does

• Provides a secure connection point between the dryer and the exhaust duct to help direct airflow out of the appliance.
• Helps reduce vent leaks that can cause poor drying performance or excess lint buildup in the cabinet/closet.
• Restores proper duct alignment to reduce rattling or vibration from a loose duct connection.
• Used when the existing collar is cracked, bent, corroded, or no longer holds the duct firmly.

• One duct collar.

• Always disconnect electrical power before servicing the dryer.
• Clean lint from the vent path before installing the new collar to ensure good airflow and reduce fire risk.
• Installation typically requires basic hand tools and a clamp or screws to secure the duct; follow the dryer's service instructions.

The Whirlpool screw is an OEM replacement part responsible for securely fastening various components and parts within Whirlpool appliances. These screws are essential for maintaining the structural integrity and safe operation of the appliance. These screws hold together critical components like panels, brackets, handles, and internal parts.

This part fixes the following symptoms:

• Loose or wobbly handles on refrigerators, ovens, or other appliances
• Vibrations or rattling noises during appliance operation
• Inability to assemble or disassemble parts during appliance repair or maintenance

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head

The Lint Filter is an OEM part for Whirlpool dryers. It is designed to trap lint and debris from the laundry during the drying cycle, preventing these particles from clogging the dryer vent and ensuring efficient operation.

You should replace this lint filter if it becomes damaged or worn out. Causes of a bad lint filter can include tears or holes in the mesh, warping from exposure to heat, or damage from mishandling. A compromised lint filter can lead to lint buildup in the dryer vent, increasing the risk of a fire hazard and reducing drying efficiency.

Symptoms of a bad Lint Filter include:

• Lint accumulating inside the dryer drum
• Longer drying times
• Noticeable damage or holes in the filter mesh

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement heating element restores proper water temperature and drying performance in your dishwasher. It helps dissolve detergent, sanitize, and dry dishes at the end of the cycle for consistent, reliable cleaning results.

• Heats wash water and boosts final rinse temperature to aid drying
• Common failure symptoms: dishes not drying, detergent not fully dissolving, cycles running long, or lukewarm water
• Helps resolve poor cleaning and milky/white residue linked to low water temperature

• Disconnect power at the breaker and shut off water supply before servicing
• Access from underneath; remove toe panel/kick plate as needed and note wiring/terminal orientation
• Inspect and reuse existing seals/hardware if applicable; check for leaks after reassembly
• After install, run a test cycle to ensure proper heating and drying

This 3/8-16 nut secures appliance components and helps prevent loosening and vibration. Replace a worn, stripped, or missing nut to restore a tight, reliable connection and consistent operation.

• Provides a 3/8-16 threaded fastener connection for applicable bolts or studs
• Helps keep brackets, panels, and other parts firmly in place
• Replaces damaged or missing hardware that can cause looseness or rattling
• Signs of failure include rounded corners, stripped threads, corrosion, or inability to tighten securely

• Disconnect power and, if applicable, shut off water and gas before servicing
• Match thread size to the original part; start threading by hand to avoid cross-threading
• Reinstall any washers/spacers in the original order; tighten securely without over-tightening
• If the original used a locking feature or threadlocker, reinstall per your product's service information

The washer is an OEM replacement part for Whirlpool clothes dryers. This part is located on the drum roller support shaft in your dryer. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.

Causes can be normal wear to bearing surfaces over extended use cycles. Accidental impacts may also potentially bend or damage shaft components.

Symptoms of a bad roller shaft include:

• Noisy squeaks or clanks emanating from within
• Jerky or unbalanced tumbling of dryer loads
• Roller assemblies binding or sticking

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Drum Support Shaft for Left Hand Threads is an OEM replacement part for Whirlpool dryers. This component is essential for securing and supporting the drum as it rotates during the drying cycle. It helps maintain the drum’s alignment and stability, ensuring smooth and efficient operation of the dryer.

Over time, the drum support shaft can become worn out or damaged due to continuous use, the weight of laundry loads, or improper installation. Additionally, exposure to high temperatures and repeated mechanical stress can cause the shaft to weaken or fail, leading to issues with the dryer’s performance.

Symptoms of a bad drum support shaft include:

• The drum not rotating smoothly or making grinding noises
• Excessive wobbling or vibrating of the drum during the drying cycle
• The dryer taking longer to dry clothes or not drying them evenly
• Visible damage or wear on the shaft or its threads
• The drum becoming misaligned or not sitting properly within the dryer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drum Support Wheel Retainer is an OEM part for Whirlpool dryers. This part secures the drum support wheels in place, ensuring that the dryer drum rotates smoothly and quietly during operation. The retainer is designed to fit precisely, preventing the support wheels from loosening or wobbling, which can lead to inefficient drying and increased wear on other components. 

Over time, retainers can wear out or become damaged, potentially leading to a loose drum support wheel. This can cause the dryer to operate noisily, vibrate excessively, or even damage the drum itself if not addressed promptly.

Symptoms of a bad Drum Support Wheel Retainer include:

• Unusual noises, such as squeaking or thumping, coming from the dryer
• Excessive vibration during operation
• The dryer drum may feel unstable or wobble when turned by hand

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Drum Support Roller is an OEM replacement part for Whirlpool dryers. It plays a crucial role in supporting and facilitating the smooth rotation of the dryer drum during the drying cycle.

Symptoms of needing to replace the drum support roller include:

• Excessive noise or grinding sounds coming from the dryer drum
• Difficulty in rotating the drum or drum not turning at all
• Visible signs of wear, cracking, or damage on the existing roller(s)
• Increased vibrations or shaking during the drying cycle

Causes of a faulty drum support roller can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or overloading.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement seal restores a tight barrier between mating parts in your appliance to help prevent leaks and keep moisture and air where they belong. Replacing a worn seal helps maintain proper performance and reduce messes.

• Forms a tight, reliable barrier between components
• Helps stop drips, seepage, and moisture wicking at the joint
• Replace if the old seal is cracked, flattened, swollen, or brittle
• Common symptoms include small puddles, dampness around the connection, or musty odors

• Disconnect power and shut off the water supply before servicing
• Note the seal's orientation; remove the old seal and clean mating surfaces of residue or mineral buildup
• Apply a light coat of food-grade silicone to ease installation
• Seat the new seal evenly without twisting; reassemble and check for leaks during initial operation

A replacement dryer drum that provides the rotating drum surface where clothes tumble and dry. Replaces a damaged or dented drum to restore smooth tumbling and prevent fabric snags or rubbing against damaged metal. What it does

• Provides the rotating drum surface that holds and tumbles laundry during drying.
• Restores a smooth interior surface to prevent clothes from catching, tearing, or snagging.
• Helps eliminate scraping, grinding or thumping noises caused by a bent or damaged drum.
• Used when visible dents, cracks or worn spots are present on the drum surface or seam.

• Disconnect power (and gas supply for gas dryers) before beginning any repair.
• Remove the dryer cabinet and front assembly to access and replace the drum.
• Inspect rollers, glides, belt and seals while replacing the drum — noisy or damaged support parts should be replaced.
• Drum replacement may require two people due to size/weight; follow OEM instructions for reassembly and alignment.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dryer Felt Seal is an OEM replacement part for Whirlpool dryers. Located around the drum, the felt seal provides a protective barrier between the drum and the cabinet.

Causes include normal material wear over time and breakdown from high-heat conditions.

Symptoms of a worn felt seal include:

• Excess lint buildup outside of the dryer near the door opening
• Signs of dust or debris accumulation within the dryer
• Reduced air flow efficiency and slow drying times

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This drum baffle (drum lifter) helps lift and separate clothes as the dryer drum turns so items tumble more evenly and dry consistently. It replaces a cracked, broken, or missing lifter to restore normal tumbling action. What it does:

• Guides and lifts garments during drum rotation to improve airflow and drying consistency
• Prevents clothes from bunching or getting caught in the drum
• Helps reduce uneven drying and extended dry times caused by a damaged lifter
• Fits on the interior drum where it secures to the drum wall

• One drum baffle (drum lifter) as described

• Disconnect power (unplug or switch off breaker) before beginning any repair
• Typical install requires access to the dryer drum; follow your model's service manual or diagram
• Inspect mounting screws or clips and replace any that are stripped or damaged

This drum baffle is the interior lifter that helps move laundry through the dryer drum for even tumbling and improved drying. It replaces a worn or broken lifter to restore proper load agitation and reduce rubbing or snagging. What it does:

• Lifts and shifts clothes as the drum rotates to promote even tumbling and airflow
• Prevents garments from bunching, which can cause uneven drying
• Reduces scraping or banging noises from a damaged or loose lifter
• Helps maintain proper drum balance during a cycle

• Designed to mount inside the dryer drum; follow your model's service manual for access and fastener locations
• Disconnect power (and gas, if applicable) before any repair to avoid shock or injury
• Inspect drum and mounting studs for damage; replace any worn fasteners for a secure fit

The Valve is an OEM part for Whirlpool dryers. It is responsible for controlling the flow of water into the dryer's steam generator, enabling the steam function during the drying cycle.

A bad water inlet valve can occur due to wear and tear, sediment buildup, or malfunctioning internal components. If you notice symptoms such as no steam being produced during the drying cycle, insufficient steam generation, or water leakage around the valve, it may be time to replace this part.

Symptoms of a bad valve include:

• No steam being produced during the drying cycle
• Insufficient steam generation
• Water leakage around the valve

Restore your Whirlpool dryer by replacing the faulty or damaged steam water inlet valve with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This small nozzle directs the water stream cleanly into the ice maker during the fill cycle, helping prevent splashing and leaks so your unit produces consistent, properly sized ice cubes.

• Channels water from the fill tube into the ice maker's fill cup/mold
• Helps maintain correct fill volume and cube formation
• Reduces stray spray that can cause frost or ice buildup
• Typical symptoms: dripping from the fill tube, ice clumps below the ice maker, hollow/small cubes, or water on the freezer shelf

• Disconnect power and shut off the water supply before servicing
• Access the fill tube/ice maker area and remove the old nozzle
• Match the original orientation and seat the new nozzle fully
• Restore water and power, then run a fill cycle and check for leaks

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This Heater Box Bracket secures the dryer's heater housing to the cabinet, keeping the heating assembly firmly mounted and aligned. Replace a bent, cracked, or missing bracket to restore stable support and reduce vibration around the heater area.

• Anchors the heater housing/box to the cabinet frame
• Maintains proper alignment and clearance for the heating element assembly
• Helps prevent rattling or rubbing noises from a loose heater housing
• A damaged bracket may leave the heater housing loose, cause vibration, or contribute to intermittent heating issues

• Disconnect power; if gas, shut off gas supply and allow the unit to cool completely
• Access the heater housing; note bracket orientation and reuse existing fasteners
• Support the heater housing and keep wiring clear while removing/installing the bracket
• After installation, verify the housing sits square and clear of the drum and wiring before restoring power

The Moisture Sensor is an OEM component specifically designed for Whirlpool washing machines. The sensor monitors moisture levels to determine when the appropriate moisture point has been reached, signaling the appliance to advance to the next step in the cycle.

Symptoms of a bad moisture sensor include: 

• Inability to advance through entire wash cycle  
• Immediate ending of cycle after short period of time
• Sensor may show moisture levels incorrectly
• LED lights indicating error codes related to moisture detection

Causes of a bad moisture sensor can be due to cracks, corrosion, or damage to its sensitive electronic components from impact or overuse. Regular cleaning and maintenance helps extend the life of the moisture sensor. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Blower Wheel is an OEM part for Whirlpool dryers. This component is essential in the dryer's air system, as it is responsible for moving air through the drum and out the vent. The blower wheel works by pulling air over the heating element, circulating it through the clothes, and expelling the moist air outside, which assists in the efficient drying of laundry.

Symptoms of a failing Blower Wheel include:

• Reduced airflow, resulting in clothes not drying properly or increased drying times
• Unusual noises like rattling or thumping, suggesting the wheel may be loose or damaged
• Excessive vibration of the dryer, especially if the blower wheel is unbalanced
• The dryer overheating due to restricted airflow if the wheel is clogged or malfunctioning

Causes of a bad blower wheel typically involve objects getting caught in the wheel, lint build-up that unbalances the wheel, or wear and tear that leads to the wheel's fins breaking or deforming.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This bulkhead is the structural inner panel that supports and seals the appliance's tub and provides mounting for controls and seals. Replaces a damaged or cracked bulkhead to restore proper alignment and prevent leaks. What it does

• Provides a sealed transition between the tub and front section to help prevent water or air leaks.
• Supports mounted components and maintains proper alignment of the tub and door assembly.
• Stops leaks, reduces rattles or vibration caused by a cracked or warped bulkhead.
• Addresses symptoms like visible cracks, loose mounting points, or fluid leaking from the front of the appliance.

• One bulkhead assembly.

• Disconnect power and shut off water before starting any repair.
• Removal typically requires taking off the front access panel or door to access mounting fasteners; have basic hand tools ready.
• Inspect existing gaskets/seals and replace if worn to ensure a watertight fit.

The Thermal Fuse is an OEM replacement part for Whirlpool dryers. It is a safety component installed within the dryer's control circuit. The fuse monitors current levels and helps prevent overheating by interrupting power flow should excessive amperage pass through the wires.

Causes of a bad fuse can include electrical surges, a malfunctioning heating element drawing too much current over time, or continual overloading of circuits.

Symptoms of a blown thermal fuse include:

• The dryer not powering on at all
• Powering on but failing to start or progress through cycles
• Buzzing or humming noises from the control area
• Repeatedly tripping of circuit breakers

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryer models.

The Thermistor is an OEM part for Whirlpool brand dryers. It is a temperature-sensing resistor that monitors air temperature changes during the drying cycle. The thermistor provides feedback to the control board on heating element performance and internal air condition. 

Symptoms of a failed thermistor include:

• Inaccurate temperature readings and selections  
• Improper or incomplete drying
• Safety issues from overheating due to lack of feedback
• Error codes displayed on the control panel

Causes can be related to normal wear and environmental exposure over time. Failure prevents the dryer from achieving optimal drying conditions.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Housing is an OEM component specifically designed for Whirlpool electric dryers. Found within the rear upper compartment, the square blower housing surrounds and supports the centrifugal fan assembly. 

Machined from durable heavy-duty plastic with ventilation slots, the blower housing channels airflow from the fan into the dual-duct exhaust system. Strategically placed mounting tabs secure the assembly in precise alignment.

Causes of a bad blower housing include cracks developing from years of constant vibration stress. Heat and exhaust moisture exposure could also warp or degrade housing material properties over time.

Symptoms of a bad housing include:  

• Noisy or unbalanced fan operation
• Reduced air velocity through ducts 
• Faulty directional airflow inside the dryer drum

Compatible with Whirlpool, Maytag, KitchenAid, and some high-efficiency Kenmore models.

This lint duct assembly routes air and lint from the dryer drum to the lint trap and exhaust, helping maintain proper airflow for efficient drying. It replaces damaged or cracked ducts that can restrict ventilation. What it does:

• Channels airflow from the drum to the lint screen and exhaust
• Guides lint toward the lint trap to help prevent buildup in the cabinet
• Restores proper venting when the original duct is cracked, warped, or broken
• Helps reduce symptoms like longer dry times, excessive lint in the cabinet, or unusual dryer noises

• Disconnect power (and gas supply if applicable) before servicing.
• Access typically requires removing the dryer front or top panel—follow your model's service manual.
• Inspect and clean nearby lint seals and the lint trap area while replacing the duct.

This heater box is the protective housing that encloses and supports the heating element in your appliance. Replacing a warped or damaged housing helps restore safe, efficient heating and protects nearby components from excessive heat.

• Holds the heater element securely and maintains proper spacing from surrounding parts
• Shields adjacent wiring and components from direct heat
• Helps maintain consistent heating performance when the original housing is heat-damaged or cracked
• Common symptoms include visible melting/warping, loose element fitment, burning odors, or repeated safety shutoffs

• Disconnect power (and gas supply, if applicable) and allow the unit to cool completely before service
• Take photos of the existing layout to aid reassembly and wire routing
• Transfer the heater element and any model-specific hardware to the new housing in the same orientation
• Ensure wiring is clear of sharp edges and heat sources; reassemble and test for proper operation

The Thermal Cut Off is an OEM part for Whirlpool dryers. This safety device helps prevent the dryer from overheating by cutting off the power to the heating element if it detects excessively high temperatures. Ensuring proper functioning of the thermal cut off is crucial for the safety and efficiency of the dryer.

Causes of a bad thermal cut off can include regular wear and tear, exposure to high temperatures over extended periods, or electrical issues within the dryer.

Symptoms of a bad thermal cut off include:

• The dryer not heating up
• The dryer shutting off mid-cycle
• The dryer not starting at all
• Unusual overheating during operation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.