Parts for Bosch WTMC6500UC/01: Burner And Motor Assemblies Parts

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This replacement mounting screw secures panels, brackets, and small assemblies to restore a snug fit and reduce rattling or loose parts. Ideal when a factory fastener is missing, damaged, or stripped. What it does:

• Fastens panels, trim pieces, brackets and internal assemblies.
• Restores proper alignment and prevents movement or vibration.
• Helps stop rattling, loose trim, or parts that shift during operation.
• Use when an original screw is missing, worn, or has a damaged head.

• Disconnect power (and water supply for water-connected appliances) before servicing.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until secure but avoid over-tightening which can strip threads or crack plastics.

This temperature limiter is a safety cutoff that stops heating when the appliance overheats, helping prevent damage and reduce fire risk. It restores normal operation only after the unit cools or the limiter is replaced. What it does:

• Senses excessive temperature and interrupts the heating circuit to prevent overheating
• Common failure symptoms: no heat or intermittent heating in the appliance
• Helps protect heating elements and internal wiring from thermal damage
• Works as a one-time/automatic cutoff safety device depending on appliance design

• Disconnect power to the appliance before accessing or replacing the limiter
• Located near the heating assembly; may require panel removal or access to the back of the unit
• Handle with care — avoid touching terminals when powered and verify wiring position before disconnecting

The Motor is an OEM component specifically designed for select Bosch electric dryers. Powering the tumbling drum, its precisely balanced construction generates consistent motion. Permanent lubrication withstands thousands of cycles.

Causes of a faulty motor commonly involve winding failure and diminishing torque output. Overheating causes internal damage necessitating replacement before hazards arise.

Symptoms of a bad motor include:

• Slow or incomplete tumbling resulting in damp loads  
• Grinding noises during operation
• Chronic imbalances necessitating resets 

Causes of a bad motor can relate to typical degradation reducing efficiency. Prolonged high-heat exposures weaken insulation requiring timely replacement. 

This OEM Bosch part is also compatible with some Miele and Asko dryers. Replace to retain smooth controlled drying for fluffy fully-ventilated fabrics long-term.
 

This fan wheel circulates air through the appliance to support drying and cooling cycles, restoring proper airflow and temperature regulation. Replaces a worn or damaged blower impeller to improve performance and reduce overheating risk. What it does:

• Spins to draw and push air through the appliance's vent and heating chamber.
• Restores airflow when a cracked or warped wheel causes weak drying or poor ventilation.
• Can reduce unusual rattling or grinding noises caused by broken blades or imbalanced rotation.
• Helps prevent overheating by maintaining designed air movement.

• One fan wheel

• Disconnect power (and gas supply, if applicable) before beginning service.
• Access the blower housing; confirm orientation and fit before final assembly.
• Inspect surrounding seals and fasteners; replace any damaged clips or screws to ensure secure mounting.
• If you hear continued noise or airflow problems after install, re-check wheel clearance and shaft/bearing condition.

The Ignition Device is an OEM part for Bosch dryers. This part ignites the gas in the dryer's burner, initiating the heating process necessary for drying clothes. By generating the spark that lights the burner's gas, it plays a pivotal role in the dryer's operation, contributing to efficient and effective drying cycles.

Causes of a malfunctioning Ignition Device include wear and tear over extended use, buildup of lint and debris affecting the ignition process, and potential damage from electrical surges.  

Symptoms indicating the need for a new ignition device include:

• The dryer fails to heat up, resulting in clothes that remain damp after a cycle.
• A noticeable lack of a sparking sound during the dryer's startup phase.
• Intermittent heating issues, where the dryer occasionally fails to produce heat.

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.