Parts for Bosch WTMC6500UC/01: Frame And Door Assemblies Parts

Door switch that detects when the appliance door is closed and signals the control so cycles can start. Replacing a faulty switch restores normal start/stop behavior and prevents operation with an open door. What it does

• Senses door closure and completes the circuit to tell the control board the door is closed.
• Stops the appliance from starting or running if the door is not properly latched.
• Common symptom: appliance won't start, stops unexpectedly, or behaves as if the door is open.
• Works with the existing door wiring and latch assembly to maintain safety interlock function.

• Disconnect power to the appliance before attempting any service.
• Note wiring and connector positions before removal; handle connectors gently to avoid damage.
• Access may require removing the inner door panel or control console—follow OEM instructions.

The Wheel is an OEM component specifically designed for select Bosch vented dryers requiring stable rotational support. As a load-bearing fixture, it maneuverably transports tumbling drum assemblies.

Causes usually arise from years of use wearing down bearings and slowing revolutions. Impacts may also deform precisely fitted wheels biasing balanced movements.

Symptoms signaling the need for a new wheel incorporate: 

• Binding or inability to smoothly transition drum assemblies  
• Grooves eroding intended contact patches for stable mobilization
• Loosened fasteners enabling unintended displacements risking stability

This OEM Bosch replacement wheel is also compatible with Thermador, Gaggenau and select Kenmore dryers relying on reliably rotating supporting structures. Correct installation restores intended operational smoothness.
 

The Foot is an OEM component specifically designed for select Bosch vented dryers requiring balanced tumbling motions. As an anchor point, it supports revolving drum weights during operation.

Causes requiring replacement relate to cumulative use wearing down attached glides and compromising smooth rotations. Physical damage exposing reinforcement fibers risks accelerated failure. 

Symptoms signaling the need for a new foot involve:

• Shaking or off-balanced drum movements from failed supports
• Loosened fasteners enabling unintended dislodging or displacement
• Cracked housings no longer stabilize intended weight distributions

This OEM Bosch replacement foot is also compatible with Thermador, Gaggenau and select Kenmore dryers relying on anchored rotational components. Correct installation restores intended weight balancing.
 

The Moisture Sensor is an OEM part for Bosch dryers. It monitors the humidity level inside the rotating drum throughout drying cycles.

Causes of a faulty moisture sensor can include mineral deposits accumulation on electrodes over time, distorting humidity readings.

Symptoms of a bad moisture sensor include:

• Incomplete drying with clothes still damp at the end of cycles
• Over-drying resulting in wrinkling or wear to fabrics
• Cycle lengths not adjusting optimally based on load moisture
• Error codes displayed relating to moisture detection

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This replacement socket connects and secures a light bulb or wiring harness inside the appliance so the light operates reliably and wiring stays stable. It restores a safe electrical connection for oven, range, or appliance lighting. What it does:

• Holds and powers the appliance light bulb or connects a small wiring harness
• Restores steady lighting when a cracked, burnt, or loose socket causes flickering or no light
• Provides a secure contact to prevent intermittent electrical connection
• Helps eliminate arcing or poor contact that can cause visible sparking or failure to light

• One replacement socket

• Disconnect power to the appliance before starting any repair to avoid shock
• Use gloves and allow bulbs and surrounding parts to cool before handling
• Inspect wiring and connectors for damage; replace if insulation or contacts are compromised

Thermister

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

Replacement mounting screw that secures panels, brackets and trim on compatible Bosch appliances. Restores proper fastening to reduce rattling, loose parts and alignment issues for safer, quieter operation. What it does:

• Secures panels, brackets, trim pieces and small appliance components.
• Replaces missing, stripped or corroded screws that allow parts to vibrate or become misaligned.
• Helps restore proper fit and reduces noise caused by loose or shifting components.
• Used wherever the original screw fastens service panels or mounting brackets.

• Disconnect power to the appliance before beginning any repair work.
• Use the correct driver bit to avoid stripping the screw head; apply firm, steady pressure.
• Do not overtighten—tighten until snug and parts are secure to avoid damaging threads or components.
• If original threads are damaged, inspect mating component and replace damaged parts or use appropriate thread repair methods.

A small mounting clip that secures exterior panels, trim or bezels to keep them aligned and reduce vibration. Replacing a damaged clip restores a snug fit and helps stop rattling or loosely seated panels. What it does:

• Holds panels and trim in the factory mounting location to maintain proper fit and alignment
• Prevents vibration and rattling caused by loose or worn fasteners
• Replaces broken, cracked, or missing clips that allow panels to sag or separate
• Works with the appliance's existing slots or mounting tabs for a secure snap-in fit

• Disconnect power to the appliance before starting any service
• Remove the adjacent trim or access panel per the service manual to reach the clip location
• Press or snap the clip into the factory slot; use pliers for leverage if needed but avoid over-forcing
• Inspect neighboring clips and mounting points for damage; replace additional clips as required

This Cap is a small protective closure used to cover and protect exposed openings or fittings on compatible Bosch appliances, helping keep dirt and moisture out for reliable operation. What it does:

• Covers exposed openings, ports, or fasteners to prevent debris and moisture intrusion
• Helps maintain proper alignment and protection of small components
• Stops small leaks or drips when used as a sealing closure in low-pressure areas
• Useful when the original cap is cracked, missing, or worn

• One replacement cap

• Install by snapping or pressing into place; no special tools typically required
• If the cap is near electrical components, disconnect power before replacing
• Replace if cracked or deformed to restore proper protection

The Lint Screen Filter is an OEM replacement part for Bosch dryers. This essential component is designed to capture lint and debris during the drying process, preventing them from accumulating within the dryer and causing potential issues.

Causes of a need to replace the lint screen filter can include excessive buildup of lint and debris over time, resulting in clogging or damage to the filter material. Regular cleaning and maintenance can help extend the lifespan of the lint screen filter.

Symptoms that may indicate a need for a replacement lint screen filter include:

• Restricted airflow and reduced drying efficiency
• Overheating or excessive heat buildup within the dryer
• Visible signs of damage or wear on the existing lint screen filter

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dryer models.

This replacement access cover protects internal components and restores a finished appearance to the appliance. It helps keep wiring and small parts shielded from moisture, dirt, and accidental contact. What it does

• Shields internal components and wiring from debris and accidental contact
• Restores the appliance's finished appearance where the original cover was cracked or missing
• Helps reduce rattling caused by a loose or damaged cover
• Can prevent moisture and small-parts ingress that may lead to further damage

• One cover

• Disconnect power and water supply before beginning any repair
• Remove any surrounding panels or fasteners to access the damaged cover; keep track of screws and clips
• Align tabs or screw holes and reinstall with the original hardware; do not force or bend the part

This genuine refrigerator door seal replaces a worn or damaged gasket to help restore proper door sealing and keep cold air inside. It reduces cycling and helps maintain consistent temperatures for stored food. What it does:

• Creates a tight seal around the refrigerator door to prevent air leaks
• Helps stop frost buildup and reduces overworking of the compressor
• Commonly replaces seals that are torn, flattened, or no longer sealing
• Fits specific Bosch refrigerator doors — improves cooling performance when seal is compromised

• Disconnect power to the appliance before starting any repair
• Remove food, shelves, and door liners as needed for access
• Warm the gasket slightly (room temperature or warm water) to ease installation; avoid open flames or excessive heat
• Inspect door frame for damage and ensure the seal is seated evenly to allow full door closure

The Door Hinge is an OEM part for Bosch dryers. This hinge is designed to securely attach the dryer door to the frame, allowing it to open and close smoothly while maintaining a proper seal during operation.

Causes of a bad door hinge can include regular wear and tear, damage from excessive force when opening or closing the door, or corrosion from exposure to moisture and heat.  

Symptoms of a bad door hinge include:

• The dryer door not closing properly or staying open
• Difficulty opening or closing the dryer door
• A misaligned dryer door
• Unusual noises or resistance when moving the door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Door Latch is an OEM part for Bosch dryers. It securely fastens the dryer door closed during operation to prevent heat loss and ensure optimal drying performance. 

Causes of a bad latch include wear and tear over time, damage due to repeated use, or failure of the latch mechanism. 

Symptoms of a bad door latch include:

• The door not fully closing or latching in the locked position
• The door popping or coming open during a cycle  
• Decreased drying efficiency due to air leaks
• Safety issues from an unsecured door

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.