Parts for Frigidaire FFGC3026SBB: 03 - Burner Parts

Burner not lighting or knob won't turn? This gas cooktop surface burner valve controls gas flow to individual burners. Moderate DIY repair.

This gas burner valve controls the flow of gas to a 1,800 BTU surface burner on your cooktop. It features a red stem and regulates gas delivery when you turn the corresponding knob. Replace this valve if the burner won't ignite, produces an uneven or weak flame, leaks gas, or if the knob turns without adjusting the flame.

Can't turn burner off or on? Burner won't light or adjust heat? Your gas cooktop burner valve likely needs replacement. DIY-friendly repair in under 2 hours.

Burner won't light, turn off, or reaches wrong temperature? This gas cooktop valve controls fuel flow to each burner. Moderate DIY difficulty repair.

Secures the ignitor assembly to your gas cooktop burner base. Replace if screw head is stripped, threads damaged, or screw is missing after disassembly.

Mounting bracket that secures cooktop components to the cabinet frame. Replace if bracket is cracked, bent, broken, or missing to restore alignment.

Gas burners won't ignite? A faulty spark module may be the issue. This part sends electrical current to igniters. DIY-friendly, takes minutes.

Replacement surface burner head for gas ranges and cooktops. Distributes gas through precision ports for even flame. Needed when original is clogged, damaged, or corroded.

Replacement burner head for gas ranges and cooktops. Mounts over the orifice to distribute flame evenly. Needed when original is cracked or damaged.

Replaces a cracked, corroded, or damaged burner on your gas range or cooktop. Installs on top to restore the heat source for your cooking zone.

Replacement gas burner for ranges and cooktops. Restores even flame distribution when original is clogged, damaged, or worn from boilovers and daily use.

This assembly combines the spark igniter and orifice holder for a 9,500-BTU cooktop surface burner. The igniter creates the spark to light the gas, while the orifice holder meters the correct gas flow to the burner. Replace this assembly if the burner won't ignite, clicks without lighting, or produces an uneven or weak flame.

This ignitor orifice assembly routes and meters gas to the oven burner so the ignitor can light the appliance reliably. Replaces a worn or damaged orifice assembly to help restore consistent ignition and safe burner operation. What it does:

• Controls gas flow to the oven burner so the ignitor can light the flame
• Helps ensure a steady, consistent ignition and proper burner operation
• Commonly replaced when ignition is slow, inconsistent, or the burner won't stay lit
• Matches OEM design for fit and function in compatible gas ranges

• One ignitor orifice assembly

• Turn off gas supply and unplug the appliance before starting work
• Follow the appliance manufacturer's service manual for proper removal and installation
• Use appropriate tools and avoid overtightening fittings to prevent leaks

This ignitor orifice assembly directs gas flow to the oven/burner igniter for reliable ignition and consistent flames. It replaces worn or clogged orifice parts to restore normal ignition performance. What it does:

• Regulates and channels gas to the igniter so the burner/oven will light
• Helps produce a steady, consistent flame for proper cooking temperatures
• Common repair when a burner or oven fails to ignite or has weak flame
• Prevents irregular ignition caused by damaged or blocked orifice passages

• One ignitor orifice assembly

• Turn off the appliance power and shut off the gas supply before starting
• Inspect fittings and seals for damage and test for leaks after installation (use approved leak-detection methods)
• Use appropriate tools and follow the appliance service manual for removal and reassembly

If your gas cooktop won't light or has delayed ignition, this ignitor orifice assembly restores the spark electrode and gas orifice for reliable starts.

Replacement tube for gas cooktops. This component connects gas line sections or attaches to valves. Replace if cracked, damaged, or leaking during use.

Replacement tube for gas cooktops. Installs in the burner assembly to direct gas flow. Order a new part if your current tube is cracked or damaged.

Regulates gas flow and pressure to your cooktop burners. Replace if damaged, worn, or if gas won't flow properly through the regulator assembly.

Replace worn cooktop shaft bushings to reduce friction and restore smooth operation. This sleeve supports rotating components for quiet performance. Confirm fit with your model number.

Converts your gas range from natural gas to LP (propane) fuel. Includes orifices and components for burners and oven. Replace when switching fuel types.

This genuine replacement screw secures appliance panels, brackets, or trim. Use it to replace a missing, stripped, or rusted fastener and restore a tight, rattle-free fit so components stay properly aligned during operation.

• Holds panels, brackets, or trim securely in place
• Replaces damaged, rusted, or missing hardware
• Helps resolve loose or rattling panels and misalignment
• Maintains proper assembly and stability during use

• Disconnect power; for gas appliances, also shut off the gas supply
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten to prevent stripping threads or damaging panels
• Repair or replace the mating clip/insert before installation

A simple metal mounting bracket that secures appliance components and keeps them aligned for reliable operation. Replaces a worn or damaged bracket to restore proper support and reduce rattling or movement. What it does:

• Provides a secure mounting point for internal components such as panels, assemblies, or modules
• Keeps parts aligned to prevent rubbing, vibration, or noise during operation
• Restores proper support when an original bracket is bent, cracked, or broken
• Helps maintain safe spacing and positioning of components to avoid interference

• One mounting bracket

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools (screwdriver, nut driver) as required; retain original fasteners unless replacement is specified
• Handle edges carefully—brackets and surrounding sheet metal can be sharp