Parts for Frigidaire FFGC3026SBC: Burner Parts

The Surface Burner Valve is an OEM replacement part for Frigidaire cooktops. It is a crucial component that regulates the flow of gas to the individual surface burners on the cooktop. Each burner has its own valve, which allows precise control over the flame size and heat output.

Symptoms of a bad Surface Burner Valve include:

• Difficulty igniting or maintaining a consistent flame on the burner
• Uneven or flickering flame
• Burner not reaching desired heat levels
• Gas smell or leaks around the burner area

Causes of a bad surface burner valve can include general wear and tear over time, debris buildup or clogging, or physical damage to the valve or related components. Exposure to high heat or improper maintenance can also contribute to valve failure.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore cooktop models.

This solenoid-operated water inlet valve controls the flow of household water into the dishwasher during fill. A working valve ensures the tub fills to the proper level for effective cleaning and stops water when the cycle ends.

• Opens and closes as signaled by the control to admit water into the tub
• Regulates fill rate/level; seals to prevent unwanted filling between cycles
• Failure symptoms can include no fill, slow fill, overfilling, or leaks at the valve/inlet area
• May trigger fill-related error or unusually long fill times

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve line pressure slowly
• Note wire harness and tubing orientation; take a photo for reference
• Use approved thread sealant/tape if specified by the manufacturer; check for leaks after installation and run a fill test

The Burner Valve is an OEM component specifically designed for Frigidaire cooktops. It controls gas flow to individual burners, providing a selection of different heat levels when operating the cooktop.

Symptoms of a bad burner valve can include: 

• Inability to light specific burners or adjust the flame height
• Uneven or intermittent burner performance   
• Gas leaks at burner valve connections
• Recurring error codes due to valve malfunctions

Causes of a bad burner valve include wear over extended usage periods, damage from water, or gas blockage impeding operation.

This OEM Frigidaire replacement is compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace before issues worsen.

The Valve is an OEM part for Frigidaire cooktops. It functions as an important component within the gas supply system that controls the flow of fuel between various points during each heating cycle. The valve works closely with the burner assembly and gas manifold to maintain consistent temperatures by facilitating proper circulation of gas throughout the system.

Symptoms of a bad valve include:

• Uneven or intermittent heating of burners  
• Burners that are difficult to light or stay lit
• Smelly gas odor coming from the range when in use
• Damage to other gas supply components requiring replacement

Causes of a bad valve can include mineral buildup over time restricting flow, failure of internal rubber seals preventing a tight seal, or issues in the valve's opening and closing mechanism.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This switch assembly replaces a worn or broken control switch to restore reliable on/off and function selection for the appliance. It provides the mechanical and electrical contacts needed for proper control operation. What it does:

• Replaces a failed control switch to restore appliance responsiveness
• Enables selection of settings and completes electrical circuits when actuated
• Commonly installed when a control no longer turns on, is intermittent, or has visible damage
• Matches OEM fit and mounting points for direct replacement

• One complete switch assembly as shown

• Disconnect power before starting any repair to avoid electrical shock
• Access may require removing panels or the control console; follow your model's service instructions
• Verify wiring location and routing before disconnecting; transfer connectors one at a time

The Ignitor Screw is an OEM component for Frigidaire ranges and ovens. It secures the igniter, a critical heating element that sparks to ignite the gas burner. 

Causes of a bad ignitor screw can include damage or stripping of the screw head from repeated removal/installation of the igniter component over time.

Symptoms of a bad ignitor screw include: 

• The igniter shaking loose and becoming disconnected
• Inability to properly tighten the igniter securely in position
• Lost or stripped screw

This genuine Frigidaire replacement screw restores secure mounting of the igniter. Proper fastening is necessary for consistent and reliable ignition of cooking appliances.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Replacement mounting bracket that secures internal appliance components to the cabinet or frame, restoring proper alignment and support. Helps reduce rattling and prevents loose or sagging parts for safer, quieter operation. What it does:

• Secures components or assemblies to the appliance frame to maintain proper alignment.
• Reduces movement and vibration that commonly cause rattling or intermittent contact.
• Helps prevent sagging or misalignment of attached parts that can affect operation.
• Simple, passive part — no electrical function.

• Disconnect power (and water, if applicable) before starting any repair.
• Use appropriate hand tools; inspect mounting holes and fasteners for damage or corrosion.
• Replace only the damaged bracket; do not overtighten fasteners to avoid cracking.

This is a ceramic glow-bar igniter for gas ovens. It heats to ignite the gas for baking or broiling, restoring reliable oven lighting and even heating without repeated clicking or open flames.

• Heats up to light the gas burner in the oven cavity
• Common fix for oven not heating, long preheat times, or burner that lights then goes out
• Designed for ovens that use a glow-bar (hot surface) ignition system

• Disconnect power and shut off gas before servicing
• Handle the ceramic element carefully; avoid touching the carbide tip
• Test for proper ignition and observe a full heat cycle after installation

The Spark Module is an OEM part for Frigidaire gas ranges. It allows precise flame control for cooking. This module sends the necessary electrical currents to the igniters at each burner, which then spark to ignite the gas. 

Causes of a bad spark module can include electrical failures, corrosion, or moisture damage, as well as wear and tear from normal use. 

Symptoms of a bad Spark Module include:

• Burners failing to ignite despite being turned on
• Intermittent ignition or weak spark generation
• Continuous clicking sounds from the burner area even after ignition
• Unlit burners leading to gas smell, indicating incomplete combustion

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Ignitor is an OEM part for Frigidaire cooktops. It provides the spark necessary to ignite the gas on your range's surface burners. It generates a spark to ignite the gas flowing to the burner, ensuring a consistent and safe flame.

A bad ignitor can be caused by wear and tear, damage, or electrical issues. Signs of a faulty ignitor include the burner not lighting or a weak or inconsistent spark.

Symptoms of a bad ignitor include:

• Burner not lighting or requiring multiple attempts to ignite
• Weak or inconsistent spark 
• Visible damage to the ignitor, such as cracks or breaks

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This is a surface burner head for a gas range/cooktop. It distributes gas from the orifice to the burner ports, helping deliver an even flame and reliable ignition when the original head is clogged, damaged, or corroded.

• Channels gas through precision ports to create a stable, even cooking flame
• Works with the burner cap and igniter for quick, consistent lighting
• Typical symptoms: burner won't light or takes multiple clicks, uneven/yellow flames, weak flame, or popping/flare-ups
• Physical issues may include blocked ports, heavy corrosion, or a warped/stripped casting

• Disconnect power and shut off gas; let the cooktop cool completely
• Lift off the burner cap; remove mounting screw(s) if present and lift off the old head
• Clean mating surfaces/orifice area; set the new head squarely and secure with existing hardware
• Restore gas and power; verify proper ignition and flame pattern

This replacement surface burner head restores a steady, even flame on your gas cooktop. It mixes gas and air and distributes the flame evenly to help ensure reliable ignition and consistent cooking performance.

• Mounts over the orifice and channels gas/air through flame ports for even heating
• Helps resolve weak, uneven, or yellow flames and delayed ignition
• Can address clicking without lighting or burners that won't stay lit
• Durable cast construction designed for repeated heating cycles

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove grates and access the burner per your model; transfer any mounting hardware from the old part if needed
• Seat the new burner head squarely over the orifice and ensure proper alignment
• Restore gas and power; test for proper ignition and flame. If any gas connections were disturbed, check for leaks with soapy water.

This burner replaces a worn or damaged unit on your range to restore reliable, even heat. Swap it in to correct poor performance caused by cracks, corrosion, or blockages so cooking results return to normal.

• Provides the heat source for a cooking zone on the range
• Common fix for damage, warping, or clogged ports/passages
• Symptoms include won't light/heat, weak or uneven heating, or irregular/yellow flame on gas models
• Visible rust, cracks, or deformation indicate replacement is needed

• Disconnect power; for gas models, also shut off the gas supply. Allow the appliance to cool completely
• Remove grate/cap or unplug element as applicable; take out screws/retainers to lift off the old burner
• Transfer reusable items from the original part (such as cap, electrode/igniter, and screws) if required by your model
• Align correctly and tighten fasteners evenly; restore utilities and test for proper operation

This burner restores proper flame distribution and ignition performance in your gas cooking appliance, helping you achieve steady, even heat for reliable boiling, simmering, and searing. What it does:

• Directs gas from the orifice through burner ports for an even flame pattern
• Works with the igniter/electrode to light the burner
• Helps reduce symptoms like uneven or weak flame, delayed ignition, or flame that lifts or makes popping noises
• Can address issues where the burner won't light or only lights partially due to damage or blockage

• 1 burner

• Disconnect power and shut off gas before servicing
• Access the burner per your model's service instructions; transfer any required hardware from the old part
• Ensure proper alignment with the igniter and orifice; tighten fasteners securely
• Restore gas and power, then inspect flame; check for leaks if any gas fittings were disturbed

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This bushing is a small replacement sleeve that supports a rotating or sliding shaft, reducing friction and wear so moving refrigerator components operate smoothly and quietly. It restores proper alignment where the original bushing is worn or damaged. What it does:

• Acts as a low-friction bearing for a shaft or pin to reduce wear on metal parts
• Helps stop wobble, binding, or noise from worn pivot or slide points
• Maintains alignment for doors, drawers, or dispenser linkages that rely on a shaft
• Prevents metal-to-metal contact that can accelerate part failure

• One bushing

• Disconnect power to the appliance before starting work
• Remove panels or trim as needed to access the worn bushing and shaft
• Press or slide the new bushing into position; avoid forcing or deforming the part
• Reassemble panels and test the component for smooth operation before regular use

The LP Conversion Kit is an OEM part for Frigidaire gas ranges. This kit allows for the conversion of the range's fuel type from natural gas to LP (liquefied petroleum) gas. It ensures the safe and efficient operation of the gas range when using LP gas as the fuel source.

Causes of a bad LP conversion kit can include incorrect installation, missing components, or damaged parts.

Symptoms of an improper fuel conversion or a bad LP conversion kit may include:

• Uneven flame
• Improper heating
• Unusual gas smells

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This genuine replacement screw secures appliance panels, brackets, or trim. Use it to replace a missing, stripped, or rusted fastener and restore a tight, rattle-free fit so components stay properly aligned during operation.

• Holds panels, brackets, or trim securely in place
• Replaces damaged, rusted, or missing hardware
• Helps resolve loose or rattling panels and misalignment
• Maintains proper assembly and stability during use

• Disconnect power; for gas appliances, also shut off the gas supply
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten to prevent stripping threads or damaging panels
• Repair or replace the mating clip/insert before installation

A simple metal mounting bracket that secures appliance components and keeps them aligned for reliable operation. Replaces a worn or damaged bracket to restore proper support and reduce rattling or movement. What it does:

• Provides a secure mounting point for internal components such as panels, assemblies, or modules
• Keeps parts aligned to prevent rubbing, vibration, or noise during operation
• Restores proper support when an original bracket is bent, cracked, or broken
• Helps maintain safe spacing and positioning of components to avoid interference

• One mounting bracket

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools (screwdriver, nut driver) as required; retain original fasteners unless replacement is specified
• Handle edges carefully—brackets and surrounding sheet metal can be sharp