Parts for Ikea 60462069A: Burner Parts

Burner not lighting or knob won't turn? This gas cooktop surface burner valve controls gas flow to individual burners. Moderate DIY repair.

This gas burner valve controls the flow of gas to a 1,800 BTU surface burner on your cooktop. It features a red stem and regulates gas delivery when you turn the corresponding knob. Replace this valve if the burner won't ignite, produces an uneven or weak flame, leaks gas, or if the knob turns without adjusting the flame.

Can't turn burner off or on? Burner won't light or adjust heat? Your gas cooktop burner valve likely needs replacement. DIY-friendly repair in under 2 hours.

Burner won't light, turn off, or reaches wrong temperature? This gas cooktop valve controls fuel flow to each burner. Moderate DIY difficulty repair.

This electromechanical switch assembly controls a specific user or internal function and restores reliable on/off or selection response. Replace a worn or damaged switch assembly to regain proper control and appliance usability. What it does:

• Acts as the electrical switching component for the appliance control circuit
• Enables user input to be registered (on/off or selection) and sent to the control system
• Common symptom: appliance won't respond when a control is pressed or switched
• Common symptom: intermittent or non-working control operation, no clicking or circuit continuity when activated

• Disconnect power before accessing or replacing the switch to avoid shock
• Access panel or control bezel removal may be required
• Handle wiring connections carefully; match terminals and secure connectors

Secures the ignitor assembly to your gas cooktop burner base. Replace if screw head is stripped, threads damaged, or screw is missing after disassembly.

Mounting bracket that secures cooktop components to the cabinet frame. Replace if bracket is cracked, bent, broken, or missing to restore alignment.

This is a ceramic glow-bar igniter for gas ovens. It heats to ignite the gas for baking or broiling, restoring reliable oven lighting and even heating without repeated clicking or open flames.

• Heats up to light the gas burner in the oven cavity
• Common fix for oven not heating, long preheat times, or burner that lights then goes out
• Designed for ovens that use a glow-bar (hot surface) ignition system

• Disconnect power and shut off gas before servicing
• Handle the ceramic element carefully; avoid touching the carbide tip
• Test for proper ignition and observe a full heat cycle after installation

Burner won't light or clicks continuously? This gas cooktop igniter creates the spark to ignite your burner. Simple fix in under 30 minutes.

Replacement surface burner head for gas ranges and cooktops. Distributes gas through precision ports for even flame. Needed when original is clogged, damaged, or corroded.

Replacement burner head for gas ranges and cooktops. Mounts over the orifice to distribute flame evenly. Needed when original is cracked or damaged.

Replaces a cracked, corroded, or damaged burner on your gas range or cooktop. Installs on top to restore the heat source for your cooking zone.

Replacement gas burner for ranges and cooktops. Restores even flame distribution when original is clogged, damaged, or worn from boilovers and daily use.

This is a metal holder that secures the burner orifice in place on a gas range cooktop. It ensures the orifice remains properly aligned with the burner so gas flows correctly for an even flame. Replace this holder if the orifice is loose, the burner flame is uneven, or the holder is cracked or damaged.

Holder component for gas cooktops. Secures and positions internal parts within the cooktop assembly. Replace if cracked, broken, or missing to restore proper fit.

Burner holder for gas cooktops. Secures the burner assembly in place. Replace if cracked, broken, or missing to properly support burner components.

This replacement tube routes water from the refrigerator's supply to the ice maker and dispenser so the ice maker fills properly and the dispenser delivers water. It restores proper water delivery when the original tube is cracked, bent or clogged. What it does

• Carries water from the internal supply line to the ice maker and dispenser
• Replaces cracked, kinked or deteriorated tubing that can restrict flow or leak
• Helps stop intermittent filling or slow water flow to the ice maker
• Prevents leaks and water damage caused by split or brittle tubing

• Disconnect power and shut off the household water supply before starting.
• Remove interior panels as needed to access the tubing and note routing before removal.
• Use proper fittings and tighten to OEM torque; replace any worn O-rings or clamps.
• After installation, restore water and power, then check all connections for leaks and verify ice maker/dispenser operation.

Replacement tube for gas cooktops. This component connects gas line sections or attaches to valves. Replace if cracked, damaged, or leaking during use.

This replacement drain tube routes defrost and condensation water away from the evaporator to the refrigerator drain system, helping prevent pooling and ice build-up. Fits specific Frigidaire refrigerator configurations. What it does

• Channels defrost and condensation water from the evaporator area to the drain pan or drain system.
• Helps stop water pooling and reduces risk of ice forming inside the freezer or refrigerator cavities.
• Works with the existing drain pan and heater components to maintain normal defrost drainage.
• Commonly replaced when cracked, clogged, split, or disconnected causing leaks or visible dripping.

• One replacement drain tube as pictured and specified by the manufacturer.

• Inspect surrounding fittings and clamps; replace any damaged fasteners to ensure a watertight connection.
• Turn off power to the appliance before accessing internal components to avoid electrical hazard.
• Route the tube exactly as the original to maintain proper drainage and avoid kinks or pinch points.
• Clean the drain path before installing the new tube to prevent repeat issues.

Burner tube for gas cooktops. Connects the gas valve to the burner assembly. Replace if cracked, corroded, or obstructing proper gas flow to burner.

Regulates gas flow and pressure to your cooktop burners. Replace if damaged, worn, or if gas won't flow properly through the regulator assembly.

Replace worn cooktop shaft bushings to reduce friction and restore smooth operation. This sleeve supports rotating components for quiet performance. Confirm fit with your model number.

LP conversion kit converts natural gas cooktop burners to propane fuel. Includes orifices and hardware to safely adapt fuel delivery system when switching fuel types.

This genuine replacement screw secures appliance panels, brackets, or trim. Use it to replace a missing, stripped, or rusted fastener and restore a tight, rattle-free fit so components stay properly aligned during operation.

• Holds panels, brackets, or trim securely in place
• Replaces damaged, rusted, or missing hardware
• Helps resolve loose or rattling panels and misalignment
• Maintains proper assembly and stability during use

• Disconnect power; for gas appliances, also shut off the gas supply
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten to prevent stripping threads or damaging panels
• Repair or replace the mating clip/insert before installation

This bracket provides a secure mounting point for the appliance's internal or external component, restoring proper alignment and support. Replaces worn, bent, or broken brackets to reduce vibration and prevent loose panels. What it does:

• Secures panels or components to the appliance frame for stable operation
• Restores proper alignment to eliminate rattling or shifting parts
• Prevents stress on adjacent fasteners and components that can cause wear
• Serves as a direct replacement for the OEM bracket when damaged

• Bracket

• Disconnect power and water before beginning any repair
• Use the correct-size fasteners and mounting holes; do not force the part into place
• Wear gloves to protect hands from sharp edges and use caution when handling metal parts
• After installation, verify panels/components are aligned and the appliance operates normally

A simple metal mounting bracket that secures appliance components and keeps them aligned for reliable operation. Replaces a worn or damaged bracket to restore proper support and reduce rattling or movement. What it does:

• Provides a secure mounting point for internal components such as panels, assemblies, or modules
• Keeps parts aligned to prevent rubbing, vibration, or noise during operation
• Restores proper support when an original bracket is bent, cracked, or broken
• Helps maintain safe spacing and positioning of components to avoid interference

• One mounting bracket

• Disconnect power to the appliance before beginning any repair
• Use basic hand tools (screwdriver, nut driver) as required; retain original fasteners unless replacement is specified
• Handle edges carefully—brackets and surrounding sheet metal can be sharp