Parts for Kenmore 791.7898815 (7917898815, 791 7898815): Burner Parts

This ferrule is a small compression fitting used to secure and seal a refrigerator water line connection, helping stop leaks and maintain proper flow to the ice maker or dispenser. It's a simple replacement to restore a tight water connection. What it does:

• Secures tubing to a compression or shutoff fitting to prevent leaks at the connection
• Restores a proper seal for water supply lines feeding the ice maker or dispenser
• Commonly used when a loose, dripping, or leaking water line is present
• Helps prevent water damage from failing or corroded fittings

• One ferrule

• Turn off the water supply and relieve line pressure before servicing
• Confirm tubing is cut square, fully inserted, and the ferrule is seated before tightening
• Tighten fittings per manufacturer guidance; avoid over-tightening which can damage tubing
• After installation, turn water back on and check carefully for leaks

This elbow is a threaded pipe fitting that redirects and secures a fluid line connection where space or alignment requires a 90° turn. It provides a compact, threaded junction to connect compatible appliance tubing or hose to a valve or port. What it does:

• Connects two threaded line ends at a 90° angle for tight routing in confined spaces
• Provides a sealed, threaded junction between a 1/2 in. NPT inlet and a 9/16-24 threaded outlet
• Helps stop leaks and maintains proper line alignment when the original elbow is worn or damaged
• Commonly used where a bent or cramped connection prevents a straight coupling

• One elbow fitting (1/2 in. NPT x 9/16-24)

• Turn off and depressurize the water supply (or system) before removing or installing fittings
• Start threads by hand to avoid cross-threading; tighten with appropriate wrench until snug
• Use plumber's tape or thread sealant only if specified by the appliance manufacturer

Gas burner won't light or clicks but doesn't ignite? Replace the igniter switch to restore spark and reliable lighting. Simple 15-30 minute DIY fix.

Oven won't heat, slow to reach temperature, or glows dull orange? This igniter fixes weak ignition. Moderate DIY repair with basic hand tools.

Oven won't light even though igniter glows? Burner lights only when valve is tapped? Replace the dual gas safety valve. DIY install in under 1 hour.

The pressure regulator with bracket controls gas flow to the range burners and is typically located behind the range. Replace when burners won't light, flame is irregular, or you smell gas during operation.

Cable retainer for cooktop installation. Secures wiring harnesses in place. Replace if broken, cracked, or missing to properly organize internal cables.

Protective wire shield for gas range safety valve. Replaces cracked, damaged, or missing guards. Installs over valve wiring for safety and protection.

This part has been discontinued by the manufacturer and is no longer available.

Secures components inside your range. Replace if the original nut is stripped, corroded, missing, or no longer holding parts firmly in place.

This part has been discontinued by the manufacturer and is no longer available.

Range door latch shield that covers and protects the top latch mechanism. Replace if cracked, broken, or missing to restore proper door alignment.

This part has been discontinued by the manufacturer and is no longer available.

This is an adhesive appliance label that replaces a worn, faded, or missing identification or warning sticker so vital product information stays visible and legible for service and safe use. What it does

• Provides a surface-mounted identification/warning label so model, rating, or safety text remains readable
• Restores faded, ripped, or illegible stickers commonly found on cabinets, doors, or control panels
• Helps technicians and owners confirm basic appliance information during service
• Prevents confusion from missing or damaged factory labels

• Clean and dry the mounting surface thoroughly before applying
• Peel backing and press firmly, smoothing from one edge to the other to remove air bubbles
• Avoid placing over vents, seals, or moving parts; align to match original label location
• Wear gloves if needed to prevent oils from reducing adhesion

This is a replacement adhesive label used to restore a faded, peeling, or missing appliance identification or instruction sticker. It helps keep model/serial, safety, or operating information legible for service and safe use. What it does:

• Restores readable identification, safety, or usage markings that were faded or damaged
• Reduces confusion from missing or illegible instructions or warnings
• Prevents misidentification that can lead to incorrect parts or procedures

• One replacement adhesive label

• Clean and dry the mounting surface before applying to ensure good adhesion
• Peel backing and press firmly, smoothing out air bubbles from the center outward
• Avoid stretching or trimming the label unless specifically required

This identification decal is a direct-fit replacement label that restores the factory-applied identification and informational marking on the appliance. Clear text and graphics help keep model/serial and key service info visible. What it does

• Replaces worn or missing identification and information labeling on the appliance
• Restores legible model, serial, and safety/operational markings so service and parts identification are easier
• Helps technicians and owners part numbers and service information during diagnosis
• Prevents misidentification caused by faded or damaged original labels

• Peel-and-stick adhesive—clean and dry the surface before applying for best adhesion
• Align carefully; once applied, most decals cannot be repositioned without damage
• No tools required for application; handle by the edges to avoid fingerprints on printed area
• Follow any appliance-specific safety steps (unplug or disconnect power) when accessing label location

This replacement appliance information label restores the printed identification, rating and safety text on the appliance so essential information is readable. Use it when the original label is faded, damaged or missing to keep markings clear and legible. What it does:

• Replaces worn or illegible manufacturer information, ratings or safety text
• Restores visibility of serial, model or rating areas so service and safety details can be read
• Helps prevent misuse by making required warnings and electrical/rating info readable
• Provides a neat, adhesive-backed identification surface for easy replacement

• One replacement information label

• Clean and fully dry the mounting surface before applying the label
• Align carefully and press firmly to ensure good adhesion; avoid repositioning after contact
• Replace only on a cool surface and avoid applying over wiring or moving parts
• Disconnect power and follow all safety precautions

This part has been discontinued by the manufacturer and is no longer available.

This adhesive identification label replaces a torn, faded or missing appliance sticker so model, serial or safety information is legible again. It helps you confirm appliance details for service, parts or safety checks. What it does:

• Restores readable model/serial and specification information that is printed on the original sticker
• Replaces damaged or faded identification and safety labels
• Makes it easier to verify the correct part or service information before repair
• Helps meet safety and inspection needs by restoring visible manufacturer info

• One adhesive identification label

• Clean and dry the mounting area before applying to ensure good adhesion
• Peel backing and press label firmly; hold for several seconds to set
• Avoid placing on textured or insulated foam surfaces where adhesion may be poor

Sound dampening insulation for gas ranges. Installs inside the range cavity to reduce noise and provide thermal protection. Replace if worn, torn, or missing.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment