Parts for Kenmore 911.32385100 (91132385100, 911 32385100): Burner Parts

This small brass fitting controls the gas flow rate to your range burner for natural gas connections. It ensures proper flame size and heating performance for medium-output burners. Replace this part if your burner flame is too large, too small, or burns with a yellow color instead of blue.

This threaded gas orifice controls the flow rate of gas to individual burners on your gas range. It ensures the correct gas-to-air mixture for proper flame size and cooking performance. Replace this orifice if burners produce yellow flames, won't stay lit, or burn too high or too low.

This hold-down bracket secures a designated component inside your appliance, keeping it firmly anchored during use. Replace a bent, broken, or missing bracket to stop movement and rattling and restore proper alignment and a stable, factory fit. What it does:

• Anchors the specified part to the appliance frame/cabinet to prevent shifting
• Reduces vibration and rattling noises during operation
• Helps maintain correct alignment and spacing for reliable performance
• Replace if the bracket is bent, cracked, corroded, or missing

What's included:

• 1 hold-down bracket

Install notes:

• Disconnect electrical power; for gas appliances, also shut off the gas supply
• Note the original orientation and screw locations before removal (a quick photo helps)
• Reuse existing mounting hardware unless your model specifies new fasteners
• Do not overtighten; verify the secured component is aligned and stable before restoring power

This insulator protects and cushions the appliance control module, helping prevent electrical shorts and physical damage to the board. It's a simple replacement that supports reliable control operation. What it does:

• Separates the control/module from the chassis to prevent shorting and rubbing
• Cushions the module to reduce vibration-related connector issues
• Helps keep wiring and components positioned correctly for consistent electrical contact
• Can reduce intermittent control problems caused by loose or damaged insulation

• Disconnect power before beginning any repair to avoid shock or damage
• Access the control panel or console per your appliance's service instructions
• Fit the insulator under/around the module as shown in the parts diagram; ensure correct orientation and secure mounting hardware
• Avoid touching circuit board components; if connectors were removed, reseat firmly before reassembly

Gas pressure regulator for cooktops and ranges. Installs on the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.

Fix burners that won't ignite or spark continuously. This spark module controls ignition for all surface burners. DIY repair in about 45 minutes.

The Switch Gas Valve is an OEM part for GE ranges. It is responsible for controlling the flow of gas to the burners, allowing them to ignite and maintain a steady flame for cooking.

Causes of a bad switch gas valve can include wear and tear over time, buildup of debris or grease, or damage from repeated use or accidental impact. These issues can hinder the valve's ability to regulate gas flow effectively.

Symptoms of a bad switch gas valve include:

• Burners not igniting
• Irregular or weak flame
• Gas odor near the stove
• Inconsistent burner performance

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Secures gas valve connections on your cooktop. Replace if loose, cracked, or causing gas leaks. Verify fit with your model number before ordering.

Gas tube assembly for cooktop burners. Connects gas supply to the rear burner. Replace if cracked, damaged, or leaking to restore safe operation.

Replace your cooktop manifold gasket seal to prevent gas leaks and ensure safe burner operation. Signs include gas odor or uneven flames. Verify fit.

ST10-16 X 7/16"

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Replacement mounting screw secures panels, brackets, and controls on ranges and ovens. Needed when original screws are missing, stripped, or damaged.

Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.

Replacement mounting screw for securing panels, trim, and brackets on ranges. Needed when original screws are missing, stripped, or damaged during repairs.