Parts for Roper 1353W4A: 05 - Burner Parts

This 3/8" outer-diameter tubing provides a reliable water-feed line for compatible appliances, restoring water flow to ice makers and dispensers when a damaged or kinked tube causes leaks or low/no water delivery. What it does:

• Replaces worn or damaged 3/8" water tubing used in supply and internal appliance water lines
• Restores proper water flow to ice makers, water dispensers and valve assemblies
• Helps stop leaks and reduces risk of kinks or pinched lines when routed correctly
• Works with standard push-fit or compression fittings where a 3/8" tube is required

• One 3/8" OD tubing piece

• Turn off and disconnect water supply before replacing tubing to prevent flooding
• Cut tubing squarely and use the correct fittings; follow OEM routing and support recommendations
• Inspect fittings, seals and valves when replacing tubing; replace damaged seals as needed

Size: 10-32 inch.

The Igniter Mounting Screw is an OEM replacement part for GE ovens and ranges. This screw secures the igniter to the burner assembly, ensuring it remains firmly in place for consistent and reliable ignition. Its precise fit and durable design help maintain the stability and functionality of the igniter.

Over time, mounting screws can become corroded, stripped, or lost during repairs or maintenance. A missing or damaged screw may result in a loose igniter, affecting the appliance's ability to ignite properly.

Symptoms of a bad or missing igniter mounting screw include:

• The igniter becoming loose or misaligned

• Difficulty securing the igniter during installation or repair
• The burner fails to ignite reliably or consistently
• Increased noise or movement of the igniter during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

The Round Style Oven or Broiler Igniter is an OEM replacement part for GE gas ranges and cooktops. It has a round design and is responsible for reliably igniting the gas burners with each use.  Range: 2.5 to 3.0 amps. 

Causes of a bad igniter can include wear and tear from repeated heating and cooling cycles, damage or defects in the electrical components, or issues arising from long-term exposure to high heat.

Symptoms of a bad igniter include: 

• Difficulty starting or unreliable ignition of gas burners  
• Burners failing to ignite with the press of the control knob
• Intermittent ignition problems
• Clicking sounds but no ignition

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

Nickel

This part has been discontinued and is no longer available.

Replacement igniter switch that restores spark ignition for gas cooktops and ranges, helping burners light reliably and reducing intermittent or no-ignite symptoms. Designed as a like-for-like control component when your original switch fails. What it does:

• Sends the electrical spark signal to the burner ignition circuit so the burner lights
• Stops clicking or sparking when the switch fails, which can cause burners not to ignite
• Addresses symptoms like intermittent ignition, continuous clicking without flame, or no spark from the burner electrode
• Works as the control point between user knob/ignition module and the spark system

• Turn off power to the appliance and shut off the gas supply before servicing
• Replace with the exact part number and match connector types; do not force-fit a non-matching switch
• After installation, test burners for proper ignition and check for gas leaks before normal use

This part has been discontinued by the manufacturer and is no longer available.

This thermostat knob replaces a worn or broken control knob so you can set and change oven or range temperature settings easily. It restores a secure grip and clear position indication for safe, consistent control. What it does

• Fits onto the thermostat/control shaft to allow manual temperature selection
• Provides a stable, easy-to-turn grip when original knob is cracked, stripped, or missing
• Helps ensure accurate user input when the control pointer or index mark is aligned
• Commonly used when the knob will not stay on, spins free, or temperature settings are hard to select

• One replacement thermostat control knob

• Disconnect power to the appliance before servicing to avoid shock or injury
• Pull off the old knob (firm pull or use a flat tool if needed) and press the new knob straight onto the control shaft until seated
• Make sure the knob index lines up with the control pointer or detent positions for correct settings
• If knob does not seat or control still malfunctions, inspect the control shaft and replace the underlying control/thermostat assembly as needed

This replacement screw secures panels and small components on your appliance to restore proper fit and help prevent rattling or loose parts. Use it wherever the original fastener has been lost or damaged. What it does:

• Secures trim, panels, or mounting brackets to keep components aligned
• Prevents vibration and rattling caused by loose fasteners
• Replaces missing or stripped screws that compromise panel fit
• Restores reliable fastening so doors and controls sit correctly

• Disconnect power before accessing internal panels or components
• Use the correct driver to avoid stripping the screw head
• Thread carefully and do not overtighten to prevent damage
• Keep small parts away from children and pets

This 8-32 thread screw fastens panels and components in compatible appliances, restoring secure mounting and stopping rattles or loose parts. Use it to replace stripped or missing fasteners and maintain proper alignment of covers and assemblies. What it does

• Secures panels, control boards, brackets, and accessory parts to the appliance chassis
• Restores proper fastening when original screws are missing, damaged, or stripped
• Helps eliminate vibration noise and loose-fit symptoms
• Matches common 8-32 appliance thread standards for a direct replacement

• One 8-32 thread screw

• Disconnect power to the appliance before beginning work to avoid shock or injury
• Use the correct-size Phillips or hex driver to prevent cam-out and head damage
• Install by hand first to engage threads, then tighten snugly—do not overtighten to avoid stripping