Parts for Ge ZIF360NNBLH: Cabinet 1 Parts

This halogen light bulb restores interior lighting so you can clearly see inside your appliance while cooking and cleaning. It replaces a burned-out or dim halogen lamp to improve visibility and safe operation. What it does:

• Provides bright, focused light for appliance interiors so you can check food and settings.
• Replaces a burned-out or flickering halogen lamp that leaves the oven or cooktop dimly lit.
• Matches the OEM part style for direct replacement when this part number is specified.
• Helps restore normal lighting without modifying the fixture or wiring.

• One halogen light bulb.

• Allow the appliance to cool and disconnect power before replacing the bulb.
• Handle the bulb by the base or wear clean gloves; oils from skin can shorten halogen bulb life.
• Test the light after installation and dispose of the old bulb properly.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Secures the evaporator fan assembly behind the rear freezer panel. Replace if cracked, rusted, or missing to restore proper fan mounting and clearance.

Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.

Rattling noise or warm temps? A broken evaporator fan blade disrupts air circulation. This repair takes 30-45 minutes with basic tools and our video guide.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that mounts and cushions the evaporator or condenser fan motor. Replace if cracked, worn, or missing to prevent vibration and noise.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

This top fan bracket secures the refrigerator's top/condenser fan assembly to the cabinet, helping keep the fan aligned for proper airflow and quiet operation. Replaces a worn or broken mounting bracket to restore stable fan mounting. What it does:

• Provides a secure mounting point for the top/condenser fan assembly
• Keeps the fan aligned to prevent rubbing, vibration, and noise
• Helps maintain proper airflow for consistent cooling performance
• Commonly replaced when bracket is cracked, bent, or broken

• Disconnect power to the appliance before beginning work
• Typical installation requires removing the top access cover and fan housing; keep track of all fasteners
• Handle sheet metal edges carefully and wear gloves to avoid cuts
• Reuse original screws if not supplied; verify fan alignment and clearance after installation

A 2 amp replacement fuse that protects low-current appliance circuits by opening when an overcurrent occurs. Install this direct-replacement fuse to restore power to control circuits and stop damage from a blown fuse. What it does:

• Interrupts current in control or low-voltage circuits when the fuse rating is exceeded
• Prevents electrical damage by opening the circuit on overloads
• Common symptoms of a blown fuse: appliance won't power on, controls are unresponsive, or intermittent operation
• Use as a like-for-like replacement matched to the original 2 amp rating

• Disconnect power to the appliance before inspecting or replacing the fuse
• Replace only when the appliance is cool and dry; avoid touching conductive ends

Left-hand top light assembly for freezers. Replace when interior lighting fails or flickers. Verify your model compatibility before ordering.

Replace your freezer's right-side top light assembly when the interior lighting fails or flickers. Restores visibility for easy access to frozen items.

Plastic plug insert that covers shelf support holes in freezer interior walls. Replaces missing, cracked, or damaged plugs for a clean finish.

Freezer not cooling or running constantly? This evaporator fan motor circulates cold air across the coil to maintain proper temperatures and efficiency.

Fix a freezer that won't cool or runs constantly. This evaporator coil absorbs heat to maintain proper temperature. Sealed system repair required.

Fix ice buildup in your freezer with this defrost heater. Solves frozen evaporator coils and drainage issues. Direct fit replacement part.

Replacement edge trim that covers and protects exposed edges on refrigerator doors or cabinets. Needed when original trim is cracked, broken, or missing.

This Evaporator trough (catch) collects defrost water from the evaporator and channels it to the refrigerator drain pan, helping prevent water buildup and freezing around the evaporator assembly. What it does:

• Catches melt water produced during automatic defrost cycles and directs it to the drain path
• Helps prevent water pooling or ice buildup inside the freezer/evaporator area
• Supports proper drainage to the condenser/drip pan to avoid leaks under the appliance
• Fits behind the evaporator cover to maintain correct water flow and containment

• One evaporator trough (catch) as shown

• Disconnect power to the appliance before starting any repair
• Remove evaporator cover/panels carefully to access the trough; avoid bending evaporator fins
• Verify correct orientation and secure with existing screws/clips; ensure drain outlet aligns with the drain tube

Replaces the stud spring on refrigerator and freezer doors. Needed when the original spring is broken, worn, or missing, affecting door alignment.

Collects defrost water under your refrigerator. Replace if cracked, leaking, or missing to prevent water damage and moisture buildup on your floor.

Left-hand link actuator for refrigerator linkage systems. Replaces worn, broken, or damaged actuators that cause erratic movement in mechanical linkages.

Spring should have GOLD color.

Mounting screw for freezer interior components and panels. Replace if stripped, corroded, or missing to secure shelves, racks, or trim properly.

Size: 8-16 x 2 inch ss.

Fixes uneven cooling or warm spots in fresh food section. This compartment fan motor circulates air to maintain consistent temperatures throughout refrigerator.