Parts for Lg 41182: Cabinet And Control Panel Assembly Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This is the complete outer door assembly for a front-load washing machine, including the door frame and glass window. It provides the sealed closure that keeps water inside the drum during wash and spin cycles. Replace this assembly if the door glass is cracked, the frame is broken, the door won't latch securely, or water leaks around the door area.

Inner door frame for washer. Structural component that supports the door assembly. Replace if cracked, warped, or damaged to restore proper door fit.

Outer door frame for front-load washers. Surrounds the door glass and attaches to the cabinet. Replace if cracked, damaged, or broken from impact.

Main outer housing that encloses and protects internal washer components. Replace if cabinet is cracked, dented, rusted, or structurally damaged.

This is a plastic cover or case that fits over the drain pump filter area on a front-load washing machine. It provides access to the drain pump filter for cleaning while keeping the filter securely enclosed during operation. Replace this cover if it is cracked, broken, or no longer snaps into place properly, which can cause water leaks near the bottom front of the washer.

Rear cover panel for washers. Protects internal components at the back of the machine. Replace if cracked, damaged, or missing to restore appearance.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replacement mounting bracket that secures internal washer components in position. Needed when original bracket is cracked, broken, or loose causing parts to shift.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

Replace your broken or cracked laundry center door handle. This exterior handle installs on the front panel for opening and closing the door.

Replaces the inner door frame trim piece that secures interior door components. Needed when the original frame is cracked, warped, or broken. Restores stability and finished appearance to your washer door assembly.

Replace your washer's damaged or missing cabinet cover panel. This exterior cover protects internal components and completes the appliance finish.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

Replacement cover cap for washers. Conceals exposed screw heads and fastener holes for a clean finish. Install when original cap is cracked or missing.

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.

Secures the drum during washer transport or relocation. Replace missing, stripped, or damaged shipping bolts to prevent internal movement and damage while moving.

Replace a broken, rusted, or missing leveling leg assembly. Installs at the base to stabilize your washer, reduce vibration, and adjust height.

Shipping bolt secures the washer drum during transportation or relocation. Replace if lost, damaged, or missing from original installation to prevent damage.

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

Washer door won't close or latch securely? This door strike ensures proper door closure for safe operation. Easy DIY fix for common latch issues.

Washer not filling or overfilling? This water level pressure switch monitors water levels and signals when to stop filling. Easy 10-minute DIY repair.

Washer won't start or shows dE/door lock error? This door switch detects if the door is closed so the cycle can begin. Easy DIY repair with video guide.

Secures the outer door boot seal to prevent water leaks. Replace if damaged, rusted, or losing tension. Includes tensioning spring. Verify fit.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.