Parts for Lg F14F2CDYP5: Cabinet And Controppanel Assemb Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Outer door frame for front-load washers. Replaces cracked, broken, or damaged frames around the door opening. Restores appearance and structure.

This cabinet cover is the outer panel that restores the appliance's exterior, protecting internal components and improving appearance. It replaces a dented, scratched, or missing outer panel to keep your unit looking and functioning as intended. What it does:

• Protects internal components from dust, debris, and incidental contact
• Restores the appliance's exterior appearance after damage or wear
• Helps maintain proper airflow paths by covering openings in the cabinet area
• Provides the correct mounting surface for adjacent trim and panels

• Disconnect power to the appliance before service to avoid shock hazard
• Remove any adjacent trim or screws to access the existing cabinet cover; keep track of fasteners
• Handle edges carefully—use gloves to avoid cuts and prevent cosmetic damage to the new panel

Top plate assembly for washer control panel area. Replaces cracked, broken, or damaged top plates. Structural component that secures and supports control.

Washer cover cap installs on the exterior panel to conceal screws or openings. Replace if cracked, broken, missing, or damaged for a clean finish.

This is a plastic cover or case that fits over the drain pump filter area on a front-load washing machine. It provides access to the drain pump filter for cleaning while keeping the filter securely enclosed during operation. Replace this cover if it is cracked, broken, or no longer snaps into place properly, which can cause water leaks near the bottom front of the washer.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

Rear cover panel for washers. Protects internal components at the back of the machine. Replace if cracked, damaged, or missing to restore appearance.

Replacement mounting bracket that secures internal washer components in position. Needed when original bracket is cracked, broken, or loose causing parts to shift.

Outer housing case for washers. Protects internal components and provides external structure. Replace if cracked, damaged, or worn for proper coverage.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Replaces the inner door frame trim piece that secures interior door components. Needed when the original frame is cracked, warped, or broken. Restores stability and finished appearance to your washer door assembly.

Protective access cover shields internal washer components from dirt and moisture. Replace if cracked, broken, or missing to restore factory protection.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.

These non-skid pads attach to the bottom of the washer's leveling legs to prevent the machine from sliding or walking across the floor during operation. They are made of durable rubber or similar grip material. Replace them if your washer vibrates excessively, moves out of position during spin cycles, or if the existing pads are worn, cracked, or missing.

Fix an unresponsive washer display or non-working touchpad with this control board assembly. Direct replacement restores front panel functionality.

Washer won't turn on or start? This main power control board assembly restores electronic control and power distribution. Moderate DIY repair.

Secures components in correct position inside your washer. Replace if cracked, broken, or worn to restore proper support and alignment for reliable operation.

This drain hose cap seals and secures the refrigerator defrost drain outlet so meltwater is directed into the drain hose instead of pooling in the cabinet. Replaces a worn or damaged cap to help stop interior leaks and water buildup. What it does:

• Seals the defrost drain outlet to prevent water from spilling into drawers or onto shelves.
• Guides defrost/meltwater into the drain hose and toward the drain pan.
• Helps reduce odors and pests entering through an open drain opening.
• Fits onto the drain outlet to replace cracked, missing, or loose caps.

• Disconnect power before working inside the refrigerator to avoid electrical hazard.
• Remove shelves and drawers as needed to access the drain outlet; clear any visible debris or ice first.
• Press the cap firmly onto the drain outlet/hose until fully seated; avoid excessive force or prying tools.
• After installation, pour a small amount of warm water down the drain to confirm proper flow and seating.

Replacement knob assembly that restores control and precise selection of settings on your appliance. Fits the original control shaft and provides a secure grip for adjusting temperature, cycle, or power settings. What it does

• Restores user control when the original knob is cracked, melted, stripped, loose, or missing.
• Provides a clear indicator/pointer for accurate selection of settings.
• Matches original fit and function to prevent slipping or uneven engagement with the control shaft.
• Helps resolve symptoms like a knob that won't turn, slips on the shaft, or has a broken pointer.

• Always disconnect power to the appliance before servicing; shut off gas supply for gas ranges.
• Typically installs without tools—remove the old knob by pulling it straight off, then press the new knob onto the control shaft.

Secures the drum during washer transport or relocation. Replace missing, stripped, or damaged shipping bolts to prevent internal movement and damage while moving.

Shipping bolt secures the washer drum during transportation or relocation. Replace if lost, damaged, or missing from original installation to prevent damage.

Replace a broken, rusted, or missing leveling leg assembly. Installs at the base to stabilize your washer, reduce vibration, and adjust height.

Secures the washer’s tub and basket during moving to prevent internal damage. If the originals are missing after a move, install replacements for transport and remove them before using the washer.

What it does

• Locks the tub and basket to limit movement in transit
• Helps prevent suspension damage and internal rattles while relocating
• Replaces missing, bent, or stripped transport bolts
• Useful for moves, storage, or service shipments

What’s included
One shipping bolt assembly (sold individually).

Install notes

• Unplug power and turn off water before service
• Insert through the rear panel into the designated mounting point; tighten snugly—don’t overtighten
• Do not operate the washer with shipping bolts installed; remove all bolts after placement
• Some models use multiple bolts and lengths—match count/positions to your owner’s manual

Usage tip
After removal, bag and tape the bolts to the cabinet so they’re on hand for the next move.

Washer not filling or overfilling? This water level pressure switch monitors water levels and signals when to stop filling. Easy 10-minute DIY repair.

Washer door won't close or latch securely? This door strike ensures proper door closure for safe operation. Easy DIY fix for common latch issues.

Washer won't start or shows dE/door lock error? This door switch detects if the door is closed so the cycle can begin. Easy DIY repair with video guide.

Secures the outer door boot seal to prevent water leaks. Replace if damaged, rusted, or losing tension. Includes tensioning spring. Verify fit.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.