Parts for Lg DLE5955G: Cabinet And Door Assembly Parts

This hinge bracket secures the refrigerator door hinge assembly so the door opens and closes smoothly and stays aligned. Replaces a worn or damaged bracket to restore proper door fit and reduce binding or sagging. What it does:

• Provides a stable mounting point for the door hinge shaft to keep the door aligned
• Restores correct door swing and sealing when original bracket is cracked or bent
• Helps stop door sag, rubbing, or uneven gaps that can cause cooling issues
• Durable molded metal/plastic construction resists wear from normal use

• One hinge bracket

• Recommended for technicians or experienced DIYers; disconnect power and empty door before starting
• Use correct screws and torque; reuse existing fasteners only if undamaged
• Inspect adjacent hinge parts and seals; replace any damaged components to ensure proper alignment
• Handle carefully to avoid damaging door finish and to maintain proper hinge geometry

The Door Latch Assembly is an OEM replacement part for LG dryers. It secures the dryer door safely closed during operation. 

Symptoms of a failing latch include:

• The door popping or swinging open during cycles  
• Difficulty fully closing and locking the door 
• Reduced efficiency as warm air leaks from gaps
• Clothing partially falling out during uncontrolled openings

Causes can be worn gears that no longer hold tight closure after extended use. Over-tightening of the door seal may also put excess strain on the assembly.

This LG OEM replacement part is also compatible with some Kenmore versions.

This safety interlock assembly secures the washer door and signals the control when it's safe to run a cycle. Replacing a faulty unit helps restore proper locking and start functions to prevent interruptions and error codes.

• Locks the washer door and confirms it is closed to allow the cycle to start
• Sends door-closed/locked status to the control throughout the cycle
• Helps prevent the door from opening during spin or when water is present
• Common symptoms: won't start, won't lock/unlock, door error (dE) messages, cycle stops mid-wash

• Disconnect power before servicing; wear cut-resistant gloves
• Access the lock at the door opening; remove the mounting screws and disconnect the harness
• Transfer connectors to the new assembly, align, and secure without overtightening
• Ensure the door strike aligns smoothly with the new lock before testing

The Door Strike is an OEM part for LG dryers. This part engages with the door catch to keep the dryer door securely closed during operation. The door strike is essential for ensuring the door remains tightly shut, allowing the dryer to function efficiently and safely.

Causes of a bad door strike can include wear and tear from regular use, damage from slamming the door, or misalignment issues that prevent it from engaging properly with the door catch. 

Symptoms of a bad door strike include:

• The dryer door not staying closed
• The dryer not starting due to the door not being securely latched
• Difficulty in latching the door
• Visible damage or wear on the strike

This OEM LG part is also compatible with Sears/Kenmore.

The Door Hinge is an OEM part for LG dryers. This hinge supports the dryer door, allowing it to open and close smoothly and securely. It ensures that the door stays aligned and functions properly, providing reliable access to the dryer drum for loading and unloading clothes.

Causes of a bad door hinge can include frequent use leading to wear and tear, physical damage from forceful opening or closing, and rust or corrosion due to exposure to moisture.

Symptoms of a bad door hinge include:

• Difficulty in opening or closing the dryer door
• The door not staying aligned or becoming loose
• Squeaking or grinding noises when moving the door
• Visible damage, bending, or rust on the hinge

This OEM LG part is also compatible with some Kenmore models.

This door gasket seals the dryer door opening to keep heat and moisture inside the drum. Replacing a worn gasket helps restore proper airflow and drying performance while reducing lint and warm air leaking around the door.

• Creates a tight seal between the door and front panel to prevent air leaks
• Helps maintain correct airflow for efficient, consistent drying
• Reduces escaping heat and humidity around the door area
• Common signs it's failing: visible wear or tears, flattened/compressed gasket, lint accumulation near the door, longer dry times, warm air leaking when the door is closed

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the door assembly as needed and separate door panels to access the gasket (procedure varies by model)
• Remove the old gasket and clean the mating groove/surface of residue and debris
• Press the new gasket fully and evenly into place; align the seam, reassemble the door, and verify an even seal

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

This safety cover is an internal protective shield used inside the dryer to guard components and help maintain proper airflow. Replacing a cracked or missing cover helps keep wiring and moving parts enclosed for safer operation. What it does:

• Shields internal wiring and components from accidental contact
• Helps channel air and lint flow as designed
• Replaces a damaged, heat-warped, or missing cover
• Helps resolve rattling/vibration noises and visible gaps where the cover mounts

• Includes 1 safety cover

• Unplug the dryer; for gas models, shut off gas and allow the unit to cool
• Access the cover location per your model's service manual; remove panels as needed
• Position the cover correctly and secure using existing hardware/clips
• Do not operate the dryer with the cover removed or loose

This drying rack sits inside the dryer drum to hold items that shouldn't tumble. It keeps shoes, sweaters, and other delicates stationary so they dry gently using the dryer's airflow and heat.

• Provides a stationary platform in the drum for rack-dry items
• Helps dry shoes, hats, sweaters, and stuffed toys without tumbling
• Replace if the rack is cracked, warped, missing, or won't stay seated
• Enables use of the rack-dry feature on compatible models

• Disconnect power and let the dryer cool before installation
• Open the door and slide the rack into the designated guides until fully seated and level
• Place items flat on the rack; avoid overloading or letting items hang over the edges
• Remove the rack before running regular tumble cycles