Parts for Frigidaire CFRE4120SW2: Cabinet / Drum Parts

This foot assembly is the adjustable leveling leg that supports and stabilizes the appliance, helping keep it level on uneven floors for proper operation and smooth door function. What it does:

• Provides a stable support point under the appliance to prevent rocking
• Allows height adjustment to level the appliance on uneven floors
• Helps maintain proper door alignment and sealing by keeping unit plumb
• Reduces vibration and noise caused by an unlevel appliance

• Unplug the appliance or disconnect power before accessing the base
• Support the appliance while adjusting or replacing the foot to prevent tipping
• Turn the leveling leg or use an appropriate wrench to raise or lower as needed

This support is a replacement mounting bracket that holds appliance components securely in place to restore proper alignment and reduce rattling or sagging. Designed to match the original fit and function for a seamless repair. What it does:

• Holds and aligns panels, drawers, or internal components to prevent sagging or misalignment
• Restores secure fitment that can stop rattling, vibration, or movement during operation
• Replaces cracked or broken brackets that cause loose or unstable parts
• Works as a direct-fit replacement when the original support is damaged or missing

• Disconnect power before starting any repair
• Handle small hardware and sharp edges carefully; use appropriate hand tools
• Verify part orientation against the removed piece before fastening
• Keep track of screws/clips and reuse only the correct fasteners

The Heater is an OEM component specifically designed for Frigidaire clothes dryers. It is responsible for generating heat levels during drying cycles to adequately dry wet clothing loads. 

Causes of a bad heater can include failures due to wear and tear over extended use, overheating damage from restricted airflow, or accumulated lint buildup impacting efficiency.

Symptoms of a bad heater include:

• Inability to achieve high heat settings 
• Slow or incomplete drying of laundry
• Error codes related to heater function
• Blowing cool or lukewarm air instead of hot air

Replacing with this OEM heater restores full drying functionality. It is compatible with your appliance and designed to withstand consistent heating cycles.  

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours before heating issues escalate further.
 

The drive belt is an OEM part for Frigidaire electric dryers. It acts as a link, transferring power from the dryer motor to turn the tumbling drum. During each drying cycle, the belt works diligently to rotate the drum and toss clothes in heated air.

Causes of belt failure involve normal wear and tear over time. Stretching, cracking, and dry rot are all contributors. Oiling or overloading the dryer can accelerate belt wear. 

Symptoms of a bad belt can include : 

• The dryer failing to start or stop 
• Excessive noise during operation
• Visible cracks or separation in the belt

This OEM replacement belt is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers. 

The Cover is an OEM part for Frigidaire dryers. It is designed to cover and protect the power cord connection on the back of the dryer, ensuring safety and preventing any damage to the electrical connection.

A bad cover can be caused by wear and tear over time, accidental damage, or improper installation. Signs of a faulty cover include cracks, breaks, or a loose fit, which can expose the power cord to potential hazards.

Symptoms of a bad cover include:

• The cover being cracked, broken, or missing
• Exposed power cord or wiring at the back of the dryer
• Potential safety hazards 

Replace your damaged or worn-out cover with this genuine OEM Frigidaire part to restore your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Harness is an OEM part for Frigidaire dryers. It is responsible for providing the electrical connection between various parts of the dryer, ensuring proper communication and voltage.

A bad harness can be caused by several factors, including wear and tear, damage from rodents or pests, or electrical issues. Signs of a faulty harness include frayed or damaged wires, loose connections, or intermittent electrical problems.

Symptoms of a bad harness include

• Intermittent power loss 
• Error codes 
• Inoperable functions or features  

Replace your damaged or worn-out harness with this genuine OEM Frigidaire part to restore your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This control panel houses the appliance's user interface and protects the console electronics while providing a clean, finished front surface. It restores button integrity and the look of the console for reliable operation. What it does:

• Replaces the console front so buttons, displays, and switches can be accessed and operated normally
• Protects underlying electronic controls from spills, dust, and everyday wear
• Helps resolve symptoms like unresponsive or loose buttons, cracked or damaged front surface, and cosmetic wear
• Matches OEM fit and mounting locations for straightforward alignment during reassembly

• One replacement control panel

• High-level task; disconnect power (unplug or turn off circuit breaker) before starting
• Remove top or trim pieces as required to access console—keep screws and retainers for reinstallation
• Handle gently to avoid bending or scratching the panel or damaging attached trim clips

This felt seal cushions and reduces vibration where a refrigerator/freezer door meets the cabinet, helping protect painted surfaces and quiet door closing. It's a simple, low-profile trim piece that keeps edges from rubbing and wearing. What it does:

• Cushions the door edge to prevent chipping, scratching, and paint wear
• Reduces noise and vibration when closing the door
• Helps maintain proper door alignment by filling small gaps at the edge
• Commonly used where the door contacts the cabinet or adjacent compartments

• Clean and dry mounting surface before installing for best adhesion or fit
• Trim to length if needed using scissors or a utility knife
• Press firmly into place; use gentle hand pressure to seat the seal
• If adhesive backing is damaged, replace with new adhesive or suitable double-sided tape

This felt seal cushions and seals a refrigerator door edge to reduce noise, prevent metal-on-metal contact, and help keep out dust and debris for smoother door operation. What it does:

• Cushions the door edge to prevent scraping and metal wear
• Dampens rattling and vibration caused by loose or worn trim
• Helps limit dust and light intrusion around the door seam
• Prevents scuffing and cosmetic damage where metal contacts metal

• Remove any old seal material and clean the mounting surface before installing
• Press the felt into place; replacement adhesive or clips may be required
• Work carefully to align the seal evenly along the edge for full coverage
• Unplug the appliance or disconnect power first and follow manufacturer service instructions

This bearing housing secures and supports a rotating shaft or assembly inside your appliance so it turns smoothly and quietly. Replacing a worn housing helps reduce noise, wobble, and drag to restore consistent, reliable motion.

• Supports and locates the bearing/shaft interface for smooth rotation
• Maintains alignment of rotating parts to reduce vibration and wear
• Helps prevent scraping or binding as the assembly turns
• When worn, may cause squealing, grinding, rumbling, or uneven rotation

• Disconnect power; shut off gas or water if applicable
• Access the assembly and support the drum/basket/drive to relieve load; note orientation before removal
• Transfer any bearing, seal, or hardware from the original housing if required
• Reassemble and verify free rotation by hand before testing

This nut is a small fastener used to secure appliance components and assemblies, helping keep panels, brackets, and hardware firmly in place for safe, quiet operation. What it does:

• Secures threaded studs, bolts, or components to prevent loosening or separation
• Helps stop rattling or vibration-related noise when used on panels or brackets
• Maintains alignment of mounted parts so doors and panels operate correctly
• Commonly used in ranges, ovens, refrigerators, and other household appliances

• Disconnect power to the appliance before servicing any internal components
• Use the correct-size socket or wrench to avoid rounding the nut
• Tighten securely but avoid over-torquing to prevent thread damage
• Replace any damaged or corroded mating hardware for a reliable fit