Parts for Crosley CFCH20LW0: Cabinet Parts

This temperature control knob replaces a worn or missing knob so you can easily adjust the cold-control setting. Restores smooth, precise temperature adjustments and a clean, factory look. What it does:

• Attaches to the cold-control (thermostat) shaft to change the temperature setting
• Provides secure grip and pointer alignment for accurate selections
• Typical failure symptoms: cracked or missing knob, stripped hub, or a knob that slips or won't turn the control

• 1 temperature control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; avoid prying at an angle to prevent shaft damage
• Align the shaft shape with the new knob and press firmly until fully seated
• The pointer aligns with the control graphics after installation

This temperature control thermostat regulates the cabinet temperature by cycling the cooling system on and off as needed. Replacing a faulty control restores consistent cooling performance and makes the setting dial respond correctly.

• Senses cabinet temperature via the capillary bulb and opens/closes contacts to start or stop the compressor
• Corrects issues such as no cooling/won't run (open control) or running constantly/won't shut off (stuck closed)
• Addresses erratic temperatures or a dial that has little or no effect on temperature
• Helps maintain stable, food-safe temperatures once adjusted

• Unplug the appliance before servicing; do not work on live circuits
• Remove the control housing/escutcheon, pull off the knob, note wire positions, and transfer any brackets as needed
• Route the new capillary in the original path; avoid kinks/sharp bends and secure the sensing bulb in the original clips
• Reassemble, restore power, and allow up to 24 hours for temperatures to stabilize; adjust the setting as needed

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material

This hinge assembly supports and pivots the appliance door so it opens smoothly and closes squarely against the gasket. Replacing a worn or bent hinge restores alignment and helps maintain a reliable seal and temperature performance. What it does:

• Provides the pivot point and support for the door
• Helps keep the door level for proper gasket contact
• Can help resolve door sagging, rubbing, or binding
• Can help with doors that won't fully close or pop back open
• Addresses play, squeaks, or visible hinge damage

• One hinge assembly

• Disconnect power and support the door before removing hinge fasteners
• Note and transfer any shims/spacers from the old hinge to the new one
• Reuse existing hardware unless the manufacturer specifies otherwise
• After installation, verify door alignment and full gasket contact; adjust as needed

Color: white. Measures about 12 inches wide by 6 inches high by 23 inches deep.

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.