Parts for Electrolux E32AR85PQSA: 03 - Cabinet Parts

Screen - drain keeps the drain path clear by trapping lint and small debris before it reaches the pump or drain hose, helping reduce clogs and improve drainage. Simple replacement restores proper water flow and drain performance. What it does:

• Traps lint, hair and small debris to help prevent clogs in the drain path
• Helps maintain consistent water drainage and pump operation
• Replace if you notice slow draining, standing water, or visible debris at the drain opening
• Sits in the appliance's drain assembly to protect downstream components

• Disconnect power to the appliance before servicing; turn off the water supply if the model requires it
• Access the drain area per your model's service instructions (remove access panel or wash tub components as needed)
• Inspect surrounding seals and hoses for damage and clean mating surfaces before installing the new screen

This cabinet breaker kit forms the insulating trim around the appliance opening. It provides a proper surface for the door or lid gasket to seal against and helps minimize condensation along the edge for clean, reliable performance.

• Creates the thermal break and finished edge around the cabinet opening
• Supports correct seating of the door/lid gasket for a consistent seal
• Helps reduce sweating or moisture at the perimeter
• Replaces cracked, warped, or missing breaker trim components

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the door/lid if required for access and retain all fasteners
• Carefully remove old breaker components and clean the mounting surfaces
• Install the new breaker and corners, align evenly, avoid overtightening, and verify the gasket seals all around

The Fan Motor Evaporator 115V is an OEM replacement part for Frigidaire refrigerators. It is a vital component responsible for circulating air and maintaining proper cooling and airflow within the refrigerator compartment.

Symptoms of a need to replace the fan motor evaporator:

• Inadequate cooling or uneven temperature distribution within the refrigerator
• Excessive frost buildup or ice accumulation on the evaporator coils
• Loud or unusual noises coming from the fan motor 
• The fan not running or running intermittently

Causes of a faulty fan motor evaporator include wear and tear over time, bearing failure, electrical malfunctions, or obstructions preventing proper airflow.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Evaporator Cover Gasket seals the perimeter of the freezer's evaporator cover to prevent air leaks that can lead to frost, moisture, and temperature swings. Replacing a worn gasket helps restore proper airflow and consistent cooling.

• Seals the evaporator cover to the liner to maintain directed airflow and contain cold air
• Helps prevent frost or ice buildup around the cover and on nearby air passages
• Can help address symptoms like temperature inconsistencies, poor cooling, or excess moisture caused by air leaks
• Replaces a torn, flattened, or missing gasket to ensure a tight cover fit

• Disconnect power before servicing; wear cut-resistant gloves
• Remove freezer shelves/bins and the evaporator cover to access the gasket
• Clean mating surfaces; press the new gasket fully into place with no gaps or twists
• Ensure air vents are unobstructed, reinstall the cover securely, then restore power

This freezer hinge kit restores proper pivot and alignment to a freezer door, helping stop sagging, binding, and air leaks. Use it to replace worn or damaged hinge components for smoother, more reliable door operation. What it does:

• Supports the freezer door pivot points and maintains correct alignment to help the door seal evenly.
• Helps resolve symptoms such as door sag, binding when opening/closing, squeaks, or visible gaps at the door edge.
• Replaces worn or damaged hinge components that can cause poor sealing and reduced cooling efficiency.
• Fits into the existing hinge mounting locations to secure the door and restore proper movement.

• Always unplug the appliance or disconnect power before starting any repairs.
• Support and brace the door before removing the old hinge—use a second person if needed to prevent injury or damage.
• Use the correct tools and follow factory torque/fastening practices; avoid overtightening to prevent misalignment.
• After installation, check door alignment and sealing; make any minor adjustments so the door closes evenly.

This drain hose carries water away from your appliance during draining to help prevent backups and leaks. Replace a cracked, clogged, or kinked hose to restore reliable water removal and protect surrounding floors and cabinets. What it does:

• Directs drain water from the outlet or pump to the designated discharge point
• Maintains proper flow; kinks or blockages can cause slow or no draining
• Helps prevent leaks from splits, pinholes, or loose connections
• Common signs: standing water, water under/around the unit, drain-related error codes, or odors

• Includes 1 drain hose

• Disconnect power and shut off water supply before servicing
• Place towels or a shallow pan to catch residual water when removing the old hose
• Note the original routing; seat connections fully, secure with clamps, and avoid sharp bends or kinks
• Run a brief drain/rinse and check all joints for leaks

This sleeve is a small spacer/bushing used in select Frigidaire-built appliances to keep mating parts aligned and moving smoothly. Replacing a worn sleeve helps eliminate play, reduce friction, and restore proper operation.

• Provides a guided, low-friction surface between parts that slide or rotate
• Maintains correct spacing/alignment to prevent wobble and rubbing
• Helps reduce wear on shafts, pins, or fasteners it interfaces with
• Typical symptoms: looseness or wobble, squeaking/scraping noises, uneven movement, or visible cracking/missing sleeve

• Disconnect power before servicing; shut off gas/water if applicable to your model
• Use your model's diagram to locate the sleeve and note orientation before removal
• Clean and inspect the mating shaft/pin or fastener; replace any severely worn components
• Seat the sleeve fully; avoid over-tightening hardware that passes through the sleeve

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

This is a replacement cabinet corner trim piece designed to restore the finished edge and appearance of your refrigerator cabinet. It covers and protects the cabinet corner where trim has cracked, broken, or gone missing. What it does

• Replaces a damaged or missing corner trim to restore a clean, finished look
• Covers exposed cabinet edges to help prevent snagging or minor moisture intrusion
• Helps keep adjacent trim and panels aligned and seated correctly
• Commonly used when trim is cracked, chipped, loose, or cosmetic finish is worn

• One cabinet corner trim piece (single)

• High-level replacement: usually snaps or presses into place; remove adjacent trim or panels if needed for access
• Use basic hand tools as required; avoid excessive force to prevent damage to surrounding panels
• If working near electrical components or lights, unplug the appliance before beginning work
• Wear gloves to protect hands from sharp edges and to improve grip during removal/installation

Specs: Hex head ,1/4-20 x 5/8

This replacement glass panel restores a smooth, sturdy surface to your refrigerator or freezer shelf/cover assembly, helping contain spills and safely support stored items so your food stays organized and accessible. What it does:

• Replaces cracked, missing, or stained shelf/cover glass to restore a flat storage surface
• Helps contain spills to prevent drips onto lower shelves or drawers
• Supports food items evenly to reduce tipping or wobbling
• Improves overall shelf stability and cleanliness

• 1 glass panel

• Unplug the appliance and wear cut-resistant gloves when handling glass
• Remove the shelf/cover assembly; note orientation before disassembly
• Carefully slide out the old glass, clean the frame/rails, and seat the new glass fully
• Ensure the panel is evenly supported on all sides before reloading items

The Glass Shelf is an OEM part for Frigidaire refrigerators. This part provides a sturdy and transparent surface for organizing food items within the fridge.  

Causes of a bad glass shelf can include accidental dropping or mishandling, heavy loads causing cracks or breakage, or thermal stress from extreme temperature changes.  

Symptoms of a bad glass shelf include:

• Cracks or chips in the glass
• Sagging or instability when supporting items
• Difficulty in fitting the shelf properly into its designated slots
• Visible wear and tear on the edges or surface of the glass

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement part is a refrigerator crisper drawer. The crisper drawer is the drawer of the refrigerator where vegetables are stored to keep them fresh. If the drawer has been cracked or is no longer operable, it might be time to replace it. Replacing this part is a very simple process.To replace the crisper drawer, simply pull the old drawer out and lift to remove it completely. After it's been removed, install the new one by gently gliding it into its track. Be sure it is aligned properly. If it opens and closes smoothly the installation was a success. This genuine OEM part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

This replacement freezer drawer restores organized, easy-access storage inside your unit. Use it to replace a cracked, warped, or missing drawer so food stays contained and the drawer slides properly on the existing rails.

• Provides slide-out storage in the freezer for organization and quick access
• Replaces a damaged or missing drawer to restore usable capacity
• Helps keep items contained so they don't fall into lower areas
• Common symptoms: cracked or broken drawer, deformed front/walls, won't slide smoothly, falls off track

• Remove food from the area; if ice buildup must be cleared, disconnect power to defrost safely.
• Pull the old drawer to the stop, then lift/tilt to release from the guides.
• Align the new drawer with both side guides and slide in evenly until fully seated.
• Do not force; verify smooth travel before reloading items.

The Adjustable Foot is an OEM part for Frigidaire dryers. This part is located at the bottom of the dryer and allows you to level it, ensuring stability and proper operation. 

Causes of a bad adjustable foot can include regular wear and tear, damage from moving the appliance, or breaking due to excessive weight or stress.  

Symptoms of a bad adjustable foot include:

• The dryer wobbling or tilting
• Difficulty in adjusting the height of the foot
• Visible damage or deformation of the foot
• Unusual noises or vibrations during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement screw fastens appliance panels and components to restore a secure fit and reduce vibration or rattling. Use when original hardware is missing, loose, or stripped to keep parts aligned and operating quietly. What it does:

• Secures panels, brackets, and trim to prevent movement and rattling.
• Replaces missing or damaged hardware that can cause loose or misaligned parts.
• Helps maintain proper component alignment for reliable operation.
• Small but essential fastener for safe, stable assembly.

• Disconnect power before servicing any electrical appliance.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten, which can strip threads or crack panels.
• Keep removed hardware organized to ensure correct reinstallation.

This 32" grille/kickplate covers the lower front of your range or oven, restoring appearance and protecting internal components from dust and debris. It gives a finished look and helps keep airflow areas clear. What it does:

• Covers and protects the appliance base from spills, dust, and debris
• Restores the finished appearance of a damaged or missing lower front panel
• Helps maintain unrestricted airflow to lower vents and components
• Common symptom: visible gap or damaged lower panel after impacts or wear

• One grille/kickplate (32")

• High-level install: typically fastened with screws along the bottom front; check existing mounting points before installing
• Use appropriate-size screwdriver and avoid overtightening to prevent panel bending
• Disconnect power to the appliance before working on areas near electrical or heating components

This hex head screw secures panels, brackets, and small components on appliances, restoring proper fit and stability. It's a direct replacement fastener when an original mounting screw is missing, loose, or damaged. What it does:

• Secures panels, brackets, trim, and internal components to prevent rattling or movement
• Replaces stripped, missing, or damaged mounting screws that cause loose parts or misalignment
• Restores reliable mechanical fastening so doors and panels sit flush and operate correctly
• Works as a general-purpose appliance mounting screw when original fasteners are worn

• Always disconnect power to the appliance before starting any repair
• Match the screw to the original location and thread engagement; start by hand to avoid cross-threading
• Use the correct driver or socket for the hex head and tighten until snug—do not overtighten
• If the original hole or threads are damaged, repair or replace the mating hardware before installing the screw

This replacement screw secures appliance components so brackets, shelves, trim, or panels stay firmly in place. Install a new screw when the original is missing, stripped, or corroded to restore a tight, rattle-free fit.

• Fastens brackets, panels, trim, or covers to the cabinet or liner
• Helps maintain alignment and reduce vibration and noise
• Direct replacement for a missing, rusted, or stripped fastener
• Use wherever your model's parts diagram specifies this screw

• Disconnect power before servicing; shut off water if working near water lines
• Match thread and length to the original location as shown in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening (especially into plastic)
• Retain and transfer any original spacers or clips used with this fastener

This is a replacement screw used to secure appliance components and panels. It provides a reliable fastener for repairs and maintenance, restoring secure attachment where the original screw is missing or damaged. What it does:

• Secures trim, panels, brackets, or small components to prevent rattling and movement
• Restores proper fit where a worn or stripped screw caused loose parts
• Helps eliminate noise caused by loose hardware
• Use as a direct replacement when the original screw is lost or damaged

• Use the matching driver bit and moderate torque to avoid stripping the head or threads
• Replace like-for-like: confirm length and thread type before installation
• Disconnect power and remove stored items from the appliance area before accessing internal panels
• If screws pull out of plastic or metal repeatedly, check for damaged threads or underlying mounting issues

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper filling and dispensing when the valve is faulty. It replaces a worn or leaking inlet valve to stop water issues and restore normal operation. What it does:

• Opens and closes to allow water into the icemaker and dispenser as needed
• Prevents water flow when closed to avoid constant filling or overflow
• Commonly linked to symptoms like no water dispensed, no or slow ice production, or intermittent water flow
• Can cause visible leaks if seals or ports fail

• Disconnect power and turn off the water supply before starting any work
• Tighten water line fittings snugly but avoid over-tightening; check for leaks after restoring water

This bracket is the factory support used to mount a component securely inside your appliance. Replacing a damaged bracket restores proper alignment and reduces vibration, keeping the part stable so it operates as designed. What it does:

• Provides a rigid mounting point for the designated component
• Maintains correct alignment to help prevent rubbing, rattling, or noise
• Replaces a cracked, bent, or missing bracket to restore secure fit
• Typical signs include vibration, a loose or misaligned part, or visible damage

• 1 bracket

• Disconnect power before servicing
• Wear cut-resistant gloves; cabinet edges can be sharp
• Reuse original screws/fasteners and any spacers or grommets from the old bracket
• Mount in the original position and tighten fasteners evenly without overtightening

This mounting bracket secures internal components or panels to restore proper alignment and reduce vibration. A simple, direct replacement that helps stop rattling, sagging or loose panels caused by a cracked or bent bracket. What it does:

• Holds and supports a component or panel to the appliance cabinet, maintaining proper fit and alignment.
• Prevents movement and vibration that can cause noise or wear.
• Replaces cracked, bent or broken brackets that cause loose panels, misalignment or rattling.
• Restores secure attachment points so doors, drawers or control housings sit correctly.

• One mounting bracket

• Disconnect power before starting any repair to avoid shock or injury.
• Basic hand tools (screwdriver, nut driver) are typically required; retain original fasteners unless replacements are provided.
• Inspect surrounding parts and mounting holes for damage; replace any worn screws or clips.

This slide is a guide rail that supports and directs a sliding drawer or rack, restoring smooth movement and proper alignment when the original is worn, cracked, or broken. Replace to stop sticking, scraping, or binding during use.

• Guides and supports a drawer or rack along its track for smooth travel
• Maintains alignment to prevent sagging, binding, or jumping off the rail
• Wear or damage can cause stiff movement, scraping noises, or misalignment
• Cracks, broken tabs, or excessive play are common signs it needs replacement

• Disconnect power and shut off water before servicing
• Remove the affected drawer/rack and note hardware orientation
• Release retainers or screws; transfer any clips or screws to the new slide
• Install and test for smooth, level operation of the drawer or rack

Replacement slide restores smooth, reliable movement for a single appliance drawer or shelf. Replacing a worn or damaged slide can stop sticking, sagging, or misaligned travel and restore proper alignment. What it does:

• Guides and supports the drawer or shelf along its track for smooth opening and closing; symptoms: sticking, binding, or incomplete travel.
• Keeps the drawer aligned and prevents sagging or tilting; symptoms: drawer sits uneven or rubs against the cabinet.
• Replaces worn, cracked or broken slide hardware to reduce noise and catch/drag during use; symptoms: grinding, rattling, or sudden drops.
• Enables consistent load support and smoother operation after wear or accidental damage.

• Disconnect power or unplug the appliance if work requires removing panels near electrical components; follow appliance safety guidance.
• Remove drawer or shelf and inspect mating rails and fasteners; replace damaged screws or clips before installing the slide.
• Use appropriate hand tools and avoid forcing parts; align slide evenly and test full travel before returning the drawer to service.

The Crisper Support is an OEM part for Frigidaire refrigerators. This part supports the crisper drawer, ensuring it slides in and out smoothly and remains securely in place.  

Causes of a bad crisper support can include repeated stress from frequent use, physical damage from heavy items, or wear and tear over time. 

Symptoms of a bad crisper support include:

• The crisper drawer not sliding in and out smoothly
• The drawer becoming misaligned or falling off track
• Visible cracks or breaks in the support structure
• Difficulty in opening or closing the crisper drawer

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A replacement stainless-steel trim kit that restores the finished look around your appliance for a clean, built-in appearance. Helps cover gaps and damaged edges and keeps the front area looking uniform. What it does

• Replaces damaged or missing exterior trim pieces to improve appearance.
• Covers gaps between the appliance and surrounding cabinetry for a finished look.
• Helps maintain a consistent stainless-steel exterior finish.
• Commonly used when original trim is bent, scratched, or otherwise cosmetically worn.

• Designed for exterior attachment; your appliance's installation manual for exact placement and hardware requirements.
• Turn off power to the appliance (or follow manufacturer safety instructions) before starting work.
• Use proper tools and handle stainless panels carefully to avoid scratching the finish.
• If fasteners or additional trim supports are required, order separately.

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed