Parts for Electrolux EFDC210TIW01: Cabinet Parts

Replace your dryer's door hinge if cracked, bent, or broken. This structural component secures the door and allows smooth opening and closing.

Leveling leg for dryers and laundry centers. Installs at the base corner to adjust height and stabilize the unit. Replace if cracked or missing.

Control panel for dryers. Mounts on the front or top of the unit. Replace if cracked, damaged, or showing wear from regular use over time.

Replacement side panel for your dryer. Covers the exterior side of the cabinet. Needed when original panel is dented, cracked, or damaged.

Replace your dryer's cracked, broken, or missing cover plate. This trim piece restores a finished look and protects internal components from dirt.

This molded duct channels airflow inside the appliance to direct exhaust and ventilation where needed. Replacing a damaged duct restores proper air movement, helping the unit run more efficiently and quietly. What it does

• Routes air between internal components to enable proper ventilation and exhaust
• Helps prevent recirculation of hot air that can reduce performance
• Reduce unusual noises caused by cracked or loose ducts
• Common symptom: reduced airflow, longer cycle times, or overheating-related shutoffs

• Disconnect power (and gas if applicable) before beginning any repair
• Access may require removing exterior panels or housing
• Inspect mounting tabs and seals; replace fasteners or gaskets if damaged

Secures internal components to the dryer chassis. Replace this mounting bracket if cracked, broken, or worn to restore stable alignment and reduce rattling.

This is a flexible rubber gasket designed to create an airtight seal. It prevents air leaks that can reduce appliance efficiency and cause temperature regulation issues. Replace this gasket if you notice visible wear, cracking, or if the seal is no longer holding properly.

Control panel cover for dryers. Replaces cracked, broken, or discolored covers. Installs on the front panel to protect controls and restore appearance.

This is a mesh lint filter that fits inside the dryer's lint trap housing to capture lint and debris during drying cycles. It helps maintain proper airflow through the dryer drum for efficient drying and reduces fire risk. Replace this filter if it is torn, warped, has holes in the mesh, or if your dryer is taking longer than usual to dry clothes.

This electronic control board manages a refrigerator's user interface and system functions so the appliance cycles, displays settings, and responds to commands correctly. Replaces a failed or malfunctioning main control module to restore normal electronic operation. What it does:

• Controls timing, compressor, fans, defrost, and user interface signals through onboard relays and logic
• Can resolve symptoms like unresponsive controls, blank or error displays, no cooling cycles, or intermittent operation
• Interfaces with sensors and switches to coordinate defrost and compressor cycles
• Uses factory connector locations and mounting points for a direct-fit replacement

• One electronic control board (main control board)

• Disconnect power to the appliance before starting any repair
• Handle the board by its edges and avoid static discharge; use an anti-static wrist strap if available
• Verify electrical connections and harness orientation before securing the board
• Follow manufacturer service instructions before installation

Dryer won't spin or makes squealing noises? This drive belt connects the motor to the drum. Common DIY repair that restores tumbling in 30-45 minutes.

Replace your dryer door seal gasket to prevent heat loss and improve drying efficiency. Worn gaskets cause longer cycles and higher energy costs. Verify fit with your model number before ordering.

Dryer front seal gasket creates a tight seal to prevent air leaks and ensure proper operation. Replace if worn, damaged, or causing noise issues.

Fix excessive vibration or wobbling during spin cycles. This mounting cone centers and stabilizes rotating components to restore smooth operation.

Replacement drum support cone for dryers. Centers and supports the rotating drum shaft for smooth operation. Needed when original cone is cracked or missing.

This is a mesh lint screen that fits into the dryer's lint trap housing, typically located inside the door opening or on top of the dryer. It captures lint and debris from clothing during the drying cycle to maintain proper airflow. Replace this screen if it is torn, warped, clogged beyond cleaning, or if your dryer is taking longer than normal to dry clothes.

Replace your dryer door gasket to restore the seal and prevent heat loss. Install when torn, cracked, or loose. Confirm fit with your model number.

Replacement mounting bolt that secures panels, brackets, or components to the dryer cabinet. Needed when original bolt is worn, missing, or stripped.

Dryer shaft support bushing provides a low-friction bearing surface for rotating shafts. Replace when you notice increased noise or rough rotation. Verify fit with your model number before ordering.

Dryer drum felt seal creates an airtight barrier between the drum and bulkhead. Replace if worn, torn, or causing squeaking noises. Verify fit with your model.