Parts for Electrolux EI33AF80WS0: Cabinet Parts

Replacement cover for upright freezer. Installs to protect internal components or provide cosmetic finish. Order if original is cracked, broken, or missing.

Replacement door hinge for upright freezers. Mounts the freezer door to the cabinet frame. Replace if hinge is cracked, bent, or no longer holds door securely.

Door hinge assembly for upright freezers. Mounts to the cabinet and door to provide smooth opening and closing. Replace if bent, cracked, or worn.

Door hinge assembly for upright freezers. Mounts to the cabinet and door to provide smooth opening and closing. Replace if bent, cracked, or worn.

Replacement cover panel for upright freezers. Installs to protect internal components or provide cosmetic finish. Order when original is cracked or missing.

This replacement nut is a factory fastener used to secure components in compatible appliances. Replacing a stripped, rounded, or missing nut restores a tight hold, reduces vibration, and helps keep assemblies properly aligned during operation.

• Threads onto a bolt or stud to clamp parts together
• Maintains correct spacing and alignment of brackets, panels, or moving parts
• Helps resolve symptoms like loose or rattling parts and excess vibration
• Ideal when original hardware is worn, damaged, or missing

• Disconnect power before servicing; shut off gas or water supply if applicable
• Match to the existing hardware and start threads by hand to avoid cross-threading
• Tighten securely without overtightening; follow any model-specific torque guidance
• Reinstall any original washers or spacers in the same order

The Freezer Leveling Leg is an OEM part for Frigidaire upright freezers. It stabilizes and balances the appliance on uneven surfaces.

Causes relate to typical bearing wear from years of weight support. Rust forms without protective finish. Cracks develop from impact damage.

Symptoms of compromised leveling legs include:

• Excessive vibrations, noise or shaking during compressor operation
• Doors that no longer close or seal properly
• Ice maker malfunctions on frost-free models

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Adjustable leveling foot for refrigerators and freezers. Installs at the base to stabilize and level the appliance. Replace if cracked or broken.

Hardware screw for securing shelves, bins, and trim panels inside refrigerators and freezers. Replace when stripped, corroded, or missing during repairs.

Replace your refrigerator's interior light bulb when it burns out or flickers. Restores clear visibility inside the fresh-food compartment. Verify fit with your model number before ordering.

Replace your refrigerator's light assembly to restore interior visibility. Install when bulb housing cracks or wiring fails. Verify fit with your model.

Replaces damaged interior light assembly to restore safe, even refrigerator illumination. Install when lights flicker, dim, or fail completely. Verify fit with your model number before ordering.

This harness with reed switch detects a magnetic field and provides a ready-made wiring connection for the appliance's door/sensor circuit, restoring reliable sensing and signal routing. What it does

• Contains a reed (magnetic) switch in-line with a multi-conductor harness to detect open/closed or presence/absence of a magnetic field
• Replaces a damaged or faulty sensor harness that can cause intermittent or no signal to the control board
• Common symptoms: appliance not sensing door/cover, controls not responding, or features tied to the sensor fail to activate
• Designed to mate with the factory connector set and routing used by the original equipment

• One complete harness with reed switch

• Verify power is disconnected before accessing wiring or replacing the harness
• Handle the reed switch and connectors gently to avoid damage; secure harness with original clips or fasteners

This replacement cover restores protection and appearance to the appliance by enclosing internal components and preventing debris or moisture entry. It's a direct-fit exterior housing piece designed to keep parts secure and reduce exposure. What it does:

• Protects internal components from dust, spills and physical damage
• Restores the appliance's finished appearance when the original cover is cracked, warped or missing
• Helps reduce noise from exposed components by keeping parts enclosed
• Minimizes risk of debris or moisture reaching electrical or mechanical parts

• Disconnect power to the appliance before beginning any work
• Use basic hand tools; handle edges carefully to avoid cuts or cosmetic damage
• Confirm fit and orientation before final fastening; do not force into place

Refrigerator won't cool properly or runs constantly? The thermistor monitors temperature and signals the control board. Moderate DIY repair.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replace a lost or worn ice scoop to restore convenient, sanitary ice handling. This durable plastic scoop makes transferring ice easy and hygienic.

Retains door shelves in your freezer, preventing items from falling. Replace if the bar is cracked, broken, or missing to secure bins properly.

Fix refrigerator not cooling, temperature fluctuations, or display errors with this electronic control board. Regulates compressor and defrost cycles.

Replacement drive motor that powers an appliance's rotating components, restoring normal operation and reliable movement. Use this motor to address rotation failures and abnormal noises so the unit can run as intended. What it does

• Turns the appliance's rotating assemblies to enable normal operation.
• Helps when the appliance won't rotate, tumble or start turning even though power is present.
• Restores consistent speed and torque for proper cycle performance.

• Disconnect power before attempting any service to avoid shock or injury.
• Verify alignment and mounting orientation; secure all fasteners to manufacturer torque where specified.
• Inspect wiring harness, connector pins and any grommets for damage; replace damaged components as needed.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

The freezer ice maker assembly is located inside the freezer compartment and automatically produces ice cubes. It includes the ice making mechanism, fill cup, ejector arms, and collection bin. Replace when ice production stops completely, ice cubes are malformed, the unit leaks water, or mechanical parts become jammed or broken.

This replacement refrigerator drawer assembly restores a smooth, sturdy bin for organizing food items. Replace a cracked, warped, or missing drawer to regain usable storage space and proper sliding action. What it does

• Provides a sliding storage bin inside the refrigerator compartment
• Keeps items contained and organized to help prevent spills
• Restores proper fit and smooth glide when matched with undamaged rails
• Typical symptoms: cracked or broken drawer, hard to open/close, falls off tracks, won't stay seated

• 1 drawer assembly

• Disconnect power and remove contents from the drawer area
• Fully extend the old drawer, lift the front, and pull to remove from the rails/glides
• Move any removable inserts from your original drawer to the new one if required by your model
• Align the new drawer with the rails and slide it in until it seats and moves smoothly; restore power

Glass shelf assembly for upright freezer interior storage. Replaces cracked, chipped, or broken shelving. Restores stable, level surface for food storage.

This drawer assembly replaces a damaged or broken refrigerator storage drawer, restoring a secure place to store produce and other refrigerated items. It gives a finished appearance and lets the drawer slide and seal correctly. What it does:

• Replaces a cracked, broken or missing storage drawer so food stays contained and organized.
• Restores proper drawer alignment and sliding action to prevent sticking or falling.
• Helps maintain internal airflow by filling the cavity designed for a storage drawer.
• Stops sharp edges or broken plastic from contacting stored items.

• Disconnect power only if removing shelves near ice/water components; otherwise remove stored food and slide out shelves.
• Remove the old drawer by sliding out and lifting per your model's instructions; install the new assembly by aligning tracks and sliding into place.
• Inspect rails and supports for damage; replace if worn to ensure smooth operation.
• Handle carefully to avoid cracking the plastic; do not use excessive force when seating the drawer.

This shelf assembly replaces a damaged or missing interior refrigerator shelf to restore storage support and organization. It provides a stable, level surface for food containers and helps keep items accessible and organized. What it does:

• Replaces a cracked, chipped, sagging, or missing refrigerator shelf
• Restores stable support for food, bins, and cookware inside the fridge
• Helps maintain organized storage and prevents items from shifting or falling
• Matches OEM fit and function for a clean, secure shelf surface

• One refrigerator shelf assembly as pictured

• Remove all food and store perishables in a safe location before replacing the shelf
• Slide shelf into existing tracks or brackets until it seats fully; follow any alignment tabs or stops
• Do not force the shelf; if it does not seat easily, check bracket orientation and clearance
• For safety, use gloves to avoid contact with sharp edges and discard broken glass responsibly

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

This slide assembly is the replacement drawer slide that restores smooth, level movement for a refrigerator drawer. It helps keep the drawer aligned and prevents sticking, scraping, or falling when opening and closing. What it does:

• Guides and supports the refrigerator drawer for smooth in-and-out movement
• Restores proper alignment when a drawer tilts, binds, or drops
• Reduces scraping, grinding, and uneven motion caused by a worn slide
• Works with the drawer track system to maintain secure operation under normal load

• Disconnect power to the appliance before beginning any repair to avoid injury.
• Basic hand tools typically required; remove the drawer and old slide to install the replacement.
• Handle edges carefully; support the drawer while attaching the new slide to prevent pinching.