Parts for Electrolux EI33AR80WS2: Cabinet Parts

Supports and aligns your refrigerator door for smooth operation and a tight seal. Replace if door sags, misaligns, or won't close properly. Verify fit with your model.

Door hinge assembly securely attaches the refrigerator door to the cabinet. Replace if hinge is cracked, broken, or worn causing door misalignment.

Door hinge assembly securely attaches the refrigerator door to the cabinet. Replace if hinge is cracked, broken, or worn causing door misalignment.

This replacement nut is a factory fastener used to secure components in compatible appliances. Replacing a stripped, rounded, or missing nut restores a tight hold, reduces vibration, and helps keep assemblies properly aligned during operation.

• Threads onto a bolt or stud to clamp parts together
• Maintains correct spacing and alignment of brackets, panels, or moving parts
• Helps resolve symptoms like loose or rattling parts and excess vibration
• Ideal when original hardware is worn, damaged, or missing

• Disconnect power before servicing; shut off gas or water supply if applicable
• Match to the existing hardware and start threads by hand to avoid cross-threading
• Tighten securely without overtightening; follow any model-specific torque guidance
• Reinstall any original washers or spacers in the same order

The Freezer Leveling Leg is an OEM part for Frigidaire upright freezers. It stabilizes and balances the appliance on uneven surfaces.

Causes relate to typical bearing wear from years of weight support. Rust forms without protective finish. Cracks develop from impact damage.

Symptoms of compromised leveling legs include:

• Excessive vibrations, noise or shaking during compressor operation
• Doors that no longer close or seal properly
• Ice maker malfunctions on frost-free models

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Adjustable leveling foot for refrigerators and freezers. Installs at the base to stabilize and level the appliance. Replace if cracked or broken.

Hardware screw for securing shelves, bins, and trim panels inside refrigerators and freezers. Replace when stripped, corroded, or missing during repairs.

Replace your refrigerator's interior light bulb when it burns out or flickers. Restores clear visibility inside the fresh-food compartment. Verify fit with your model number before ordering.

Replace your refrigerator's light assembly to restore interior visibility. Install when bulb housing cracks or wiring fails. Verify fit with your model.

Replaces damaged interior light assembly to restore safe, even refrigerator illumination. Install when lights flicker, dim, or fail completely. Verify fit with your model number before ordering.

This harness with reed switch detects a magnetic field and provides a ready-made wiring connection for the appliance's door/sensor circuit, restoring reliable sensing and signal routing. What it does

• Contains a reed (magnetic) switch in-line with a multi-conductor harness to detect open/closed or presence/absence of a magnetic field
• Replaces a damaged or faulty sensor harness that can cause intermittent or no signal to the control board
• Common symptoms: appliance not sensing door/cover, controls not responding, or features tied to the sensor fail to activate
• Designed to mate with the factory connector set and routing used by the original equipment

• One complete harness with reed switch

• Verify power is disconnected before accessing wiring or replacing the harness
• Handle the reed switch and connectors gently to avoid damage; secure harness with original clips or fasteners

This replacement cover restores protection and appearance to the appliance by enclosing internal components and preventing debris or moisture entry. It's a direct-fit exterior housing piece designed to keep parts secure and reduce exposure. What it does:

• Protects internal components from dust, spills and physical damage
• Restores the appliance's finished appearance when the original cover is cracked, warped or missing
• Helps reduce noise from exposed components by keeping parts enclosed
• Minimizes risk of debris or moisture reaching electrical or mechanical parts

• Disconnect power to the appliance before beginning any work
• Use basic hand tools; handle edges carefully to avoid cuts or cosmetic damage
• Confirm fit and orientation before final fastening; do not force into place

Refrigerator won't cool properly or runs constantly? The thermistor monitors temperature and signals the control board. Moderate DIY repair.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

This water inlet valve controls the flow of water from the household supply into the refrigerator for the ice maker and dispenser, restoring water delivery when the original valve fails. Easy replacement for common flow and leak issues. What it does:

• Opens and closes to allow water into the icemaker and dispenser when needed
• Stops water flow to prevent overfilling or continuous flow when faulty
• Commonly replaced when water does not dispense or ice production stops
• Can be the source of slow fill, intermittent flow, or visible leaks at the valve area

• One water inlet valve

• Disconnect power and shut off the water supply before starting work
• Drain remaining water from lines and catch any residual with a towel
• Verify fittings and tubing are seated and tightened to prevent leaks after install

This rigid refrigerator tubing routes water inside the appliance to the dispenser, ice maker, or internal components, helping maintain a steady water supply and prevent leaks when intact. What it does:

• Carries water between the inlet, valve, ice maker, dispenser, or internal components.
• Restores water flow when original tubing is cracked, pinched, or blocked.
• Prevents pooling or dripping caused by damaged internal water lines.
• Helps stop intermittent or complete loss of water to the dispenser/ice maker when replaced.

• One replacement tube as pictured.

• Turn off the water supply and unplug the appliance before starting any work.
• Use proper fittings and hand-tighten connections; replace damaged clamps or seals.
• Inspect adjoining components (valve, fittings, connectors) for damage while replacing tubing.

Retains door shelves in your freezer, preventing items from falling. Replace if the bar is cracked, broken, or missing to secure bins properly.

Fix refrigerator not cooling, temperature fluctuations, or display errors with this electronic control board. Regulates compressor and defrost cycles.

Directs water flow to your refrigerator's filter housing for filtered water to the dispenser and ice maker. Replace if leaking or damaged. Verify fit.

A replacement PurePour pour-through funnel for refrigerator water-filter filling—helps channel water directly into the PurePour filter housing to reduce spills and ensure the cartridge fills and seats correctly. What it does:

• Funnels water cleanly into the PurePour filter housing to minimize splashing and wasted water.
• Promotes even filter cartridge filling so the filter can seat properly.
• Use when you notice water spilling, trouble filling the filter, or the filter won't seat securely.
• Works as the direct replacement component for the PurePour pour-through fill assembly.

• One replacement pour-through funnel.

• Turn off the refrigerator's water supply before removing or installing the funnel.
• Wipe the area dry and seat the funnel fully into the filter housing; no special tools typically required.
• Inspect seals and the filter cartridge for damage while replacing the funnel.

This replacement refrigerator drawer assembly restores a smooth, sturdy bin for organizing food items. Replace a cracked, warped, or missing drawer to regain usable storage space and proper sliding action. What it does

• Provides a sliding storage bin inside the refrigerator compartment
• Keeps items contained and organized to help prevent spills
• Restores proper fit and smooth glide when matched with undamaged rails
• Typical symptoms: cracked or broken drawer, hard to open/close, falls off tracks, won't stay seated

• 1 drawer assembly

• Disconnect power and remove contents from the drawer area
• Fully extend the old drawer, lift the front, and pull to remove from the rails/glides
• Move any removable inserts from your original drawer to the new one if required by your model
• Align the new drawer with the rails and slide it in until it seats and moves smoothly; restore power

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

Replace your refrigerator's drawer assembly if cracked, broken, or no longer sliding smoothly. Installs in fresh food or freezer compartment.

Replacement shelf assembly for refrigerator fresh food compartment. Restores storage space when original is cracked, broken, or missing.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

This slide assembly is the replacement drawer slide that restores smooth, level movement for a refrigerator drawer. It helps keep the drawer aligned and prevents sticking, scraping, or falling when opening and closing. What it does:

• Guides and supports the refrigerator drawer for smooth in-and-out movement
• Restores proper alignment when a drawer tilts, binds, or drops
• Reduces scraping, grinding, and uneven motion caused by a worn slide
• Works with the drawer track system to maintain secure operation under normal load

• Disconnect power to the appliance before beginning any repair to avoid injury.
• Basic hand tools typically required; remove the drawer and old slide to install the replacement.
• Handle edges carefully; support the drawer while attaching the new slide to prevent pinching.

Replace your refrigerator's interior light assembly to restore compartment illumination. Includes lens and socket in one piece. Verify fit with your model.

Refrigerator freshness booster refill absorbs and removes odors to maintain freshness. Replace when absorption material depletes. Verify fit with model.

Shoulder screw secures internal panels and components in refrigerators. Replace if missing, stripped, or damaged. Hi-lo quadrex head, M4.2 x 1 thread.

Exterior trim piece that shields and finishes refrigerator openings. Replaces cracked, broken, or missing cover to restore proper fit and appearance.

Positions and supports refrigerator shelves for secure, level placement. Replace worn, broken, or missing spacers to eliminate wobble and restore fit.