Parts for Electrolux EI33AR80WS2: System Parts

If your freezer isn't cooling properly or runs constantly, the condenser coil may have failed. This assembly restores heat exchange for efficient cooling.

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Fix a refrigerator that won't cool or runs constantly with this inverter compressor drive module. Controls variable-speed operation for efficient cooling.

Fixes intermittent power issues or control failures in your freezer. This wiring harness restores reliable electrical connections between components.

This support mounting bracket secures internal components and panels so your appliance stays stable and functions reliably. It replaces a worn or broken bracket to restore proper alignment and reduce rattling or loose parts. What it does:

• Provides a secure mounting point for internal panels or components
• Restores proper alignment to reduce vibration, noise, and movement
• Helps maintain structural stability of the appliance cabinet or assembly
• Works where a damaged or missing bracket causes loose or sagging parts

• One support mounting bracket

• Install using original fasteners; inspect adjacent parts for wear before reassembly
• Disconnect power and follow safety procedures before servicing the appliance
• If screws or clips are stripped or missing, replace them with matching hardware

Fix frost buildup and cooling issues with this defrost heater. Restores proper defrost cycles and eliminates excessive ice in your refrigerator or freezer.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Fixes power issues, intermittent operation, or control failures in your freezer. This wiring harness assembly replaces damaged electrical connections.

Cover assembly for refrigerator interior components. Replaces cracked, broken, or missing covers. Direct fit replacement part for specific models.

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Refrigerator not cooling or freezing over? A failed evaporator fan motor stops air circulation. Straightforward DIY repair restores proper cooling.

Refrigerator running hot or not cooling properly? A failed condenser fan motor prevents heat dissipation. This assembly replaces the complete motor unit.

Fix a refrigerator that won't cool or runs constantly with this compressor. Resolves warm temps and frequent cycling. Advanced repair, 2-4 hours.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

This Power Supply Frame is an OEM part for Frigidaire refrigerators. It provides stability and support to the power supply components within the refrigerator.

Causes of a Bad Part: Exposure to moisture or physical damage can lead to corrosion or structural weakening of the frame. Continuous power fluctuations might also contribute to its deterioration.

Symptoms of a Bad Part:

• Loose or unstable power connections
• Corrosion or rust on the frame
• Power supply instability

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models

Fix a refrigerator that won't cool, has erratic temperatures, or stops defrosting with this electronic control board. Regulates temperature and cycles.

Fixes unresponsive controls, blank displays, or frozen settings. This electronic control board restores user commands and operation cycles in your appliance.

This baffle directs cold air inside the refrigerator to help maintain even temperatures and proper airflow. Replacing a damaged or missing baffle restores intended air circulation and helps performance. What it does

• Channels and directs airflow between compartments for more consistent cooling.
• Helps prevent warm spots caused by blocked or misdirected air.
• Reduces stress on the cooling system by restoring designed airflow paths.
• Commonly replaced when cracked, broken, or missing, or when airflow is visibly obstructed.

• Unplug the appliance or disconnect power before starting any work.
• Remove food, shelves, and drawers as needed for access; handle components gently to avoid damage.
• Inspect mounting points and gaskets; replace any damaged fasteners or seals.
• Refer to OEM instructions for model-specific removal/replacement steps.

This cover drain jumper is a molded drain-channel cover that helps route defrost and condensate water into the refrigerator drain system, preventing water from pooling inside the cabinet and reducing ice buildup. What it does:

• Guides defrost and condensate water into the drain channel so it flows to the drain pan
• Helps prevent water from pooling at the back or bottom of the fresh-food compartment
• Reduces the chance of ice forming around the evaporator or in the drain path
• Fits into the drain housing to maintain proper condensate flow

• Disconnect power to the appliance before beginning any service.
• Remove shelves/panels that obstruct access to the drain area; handle plastic parts gently to avoid breakage.
• Make sure the drain channel is clear of debris and ice before installing the cover for best results.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

Harness cable tie secures and organizes wiring inside your appliance. Replace if damaged, cracked, or no longer holding wires firmly in place.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.