Parts for Electrolux EW23CS70IB0: 07 - Cabinet Parts

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Fix refrigerator lights that won't turn on when door opens. This door light switch is a simple snap-in replacement. Easy 10-minute DIY repair.

Genuine mounting screw secures panels, brackets, and covers inside your refrigerator. Replace missing, stripped, or corroded fasteners to restore secure fit.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.

Adjustable front roller assembly for refrigerators. Supports appliance weight and allows leveling adjustments. Replace if roller is damaged or bolt is broken.

Adjustable hinge kit for refrigerator doors. Includes components to secure and adjust door hinges. Replace if worn, broken, or door won't seal properly.

Adjustable hinge kit for refrigerator doors. Includes components to secure and adjust door hinges. Replace if worn, broken, or door won't seal properly.

Replacement corner trim that covers the cabinet edge of your refrigerator. Restores a finished look to cracked, chipped, or missing corner pieces.

OEM mounting bracket that secures the hinge and pin assembly inside your refrigerator. Replace if cracked, broken, or missing to restore proper alignment.

Supports and aligns the refrigerator door at the hinge pivot point. Replace if cracked, bent, or worn to restore stable door operation and proper sealing.

Electrical wire harness for side-by-side refrigerators. Connects internal components. Replace if wires are frayed, connectors damaged, or broken.

Plastic grommet that secures shelves and basket rails to the freezer wall. Replace if cracked, loose, or falling out of the mounting hole.

Hex head screw secures refrigerator door hinges to the cabinet. Replace if missing, stripped, or lost during moves or repairs. 1/4-20 thread size.

Adjustable front roller assembly for refrigerators. Supports appliance weight and allows leveling adjustments. Replace if roller is damaged or bolt is broken.

Replacement screw for refrigerator panels, brackets, and covers. Secures interior and exterior components. Needed when original is missing, stripped, or corroded.

Mounting channel that secures refrigerator shelves to interior walls. Replace if cracked, broken, or no longer holding shelves securely in place.

This switch board is the circuit board behind the control buttons. It reads your selections and relays them to the appliance's control system, restoring reliable button response when the original board is damaged or worn.

• Interprets button/selector inputs and sends signals to the main control
• Helps resolve unresponsive buttons, intermittent inputs, or incorrect function selection
• Visual issues can include burnt components, cracked traces, or corrosion on the board

• Disconnect power to the appliance before servicing
• Use ESD precautions; handle the board by its edges and avoid touching contacts
• Photograph/label connectors and transfer them one at a time to the new board
• Ensure all harnesses are fully seated and routed to avoid pinching during reassembly

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.

Secures panels, brackets, handles, and trim inside your refrigerator. Replace missing, stripped, or damaged screws to eliminate rattling and looseness.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Insulated cardboard cover assembly that installs on the rear bottom of your refrigerator. Replaces a cracked, torn, or missing original cover.

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Light stays on or won't turn on when you open the fridge door? This door-activated switch controls interior lighting. Simple DIY fix for most models.

Rear support clip that holds the crisper cover shelf in place. Replace when broken, snapped, or cracked to restore stability to your crisper drawer area.

Supports the glass crisper cover in your refrigerator. Replace if cracked, broken, or missing. Installs on the refrigerator wall above the crisper drawer.

This air duct assembly routes cold air from the evaporator to the refrigerator compartments to help maintain even cooling and proper airflow. Replaces a damaged or cracked duct that causes uneven temperatures or restricted airflow. What it does:

• Channels cooled air from the evaporator to the freezer and fresh-food sections
• Restores correct airflow when cracks, breaks, or displacements cause reduced cooling
• Helps prevent frost buildup by directing air through designed passages
• Works with the evaporator fan and housing to maintain consistent compartment temperatures

• Disconnect power to the appliance before beginning any service
• Typically accessed by removing interior panels or the evaporator cover; handle plastic parts gently to avoid damage
• Verify orientation and fit before final reassembly; ensure seals and gaskets are seated correctly

This return air seal keeps refrigerator airflow channels sealed so cold air returns to the evaporator properly, helping maintain consistent temperatures and reduce frost and moisture issues. It replaces a worn or damaged return-air gasket. What it does

• Seals the return-air opening to direct cold air back to the evaporator
• Helps maintain even cooling and prevents warm air infiltration
• Reduces frost, moisture buildup, and uneven temperature zones
• Commonly replaced when you notice poor cooling, excessive frost, or air leakage noises

• One return air seal

• Disconnect power before starting work
• Remove any trim or panels that block access to the return-air opening
• Seat the seal into the channel or mating surface; some installations use adhesive or retainers—follow the manufacturer's instructions

Refrigerator harness retaining clip secures wiring in place. Replace if broken or loose to prevent wire damage. Confirm fit with your model number.

Wiring harness for side-by-side refrigerators. Connects electrical components inside the unit. Replace if wires are frayed, damaged, or broken.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.