Parts for Electrolux EW23CS70IB0: 05 - Refrigerator Door Parts

This gray magnetic refrigerator door gasket replaces the perimeter seal on the fresh food door. It creates an airtight closure that keeps cold air in, blocks humid air, and helps prevent temperature swings, frost, and condensation. What it does:

• Seals the door perimeter with a flexible magnetic edge to stop air leaks
• Helps maintain proper refrigerator temperature and reduce frost/condensation near the door
• Restores smooth closing when the old gasket is torn, shrunken, or warped
• Typical symptoms: visible gaps, moisture on the gasket, frequent cycling, or food warming near the door

• 1 gray magnetic refrigerator door gasket

• Disconnect power before servicing
• Warm the new gasket with a hair dryer or hot water to relax folds for easier seating
• Remove the old gasket; press/fasten the new gasket evenly into the door channel or retainer, ensuring corners are fully engaged
• Close the door and check for uniform contact; adjust hinges or gently reshape with warm air as needed and allow the gasket to set with the door closed

This #10-32 x 3/4-inch machine screw secures appliance components such as panels, brackets, and handles. Using the correct length and thread helps restore a snug, rattle-free hold wherever this screw is specified by the manufacturer.

• Fastens components with a #10-32 machine thread and 3/4-inch length
• Helps keep panels, trim, brackets, or handles secured and aligned
• Replaces missing, stripped, or corroded hardware
• Common signs include loose or wobbly parts, rattling, missing screws, or damaged screw heads/threads

• Disconnect power before servicing; if working near a water connection, shut off the water supply
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping plastic or threads
• Reuse any model-specific washers or spacers if present

This refrigerator dispenser bearing supports the auger shaft so it spins smoothly during ice dispensing. Replacing a worn bearing restores quieter, more reliable ice delivery and helps prevent binding or uneven crushing of cubes. What it does

• Supports and centers the ice auger/crusher shaft inside the ice bucket
• Reduces friction to allow smooth, consistent rotation
• Wear can cause grinding or squealing during dispensing
• Symptoms include slow/no ice dispensing, jamming, or intermittent operation

• 1 bearing

• Disconnect power and turn off the water supply before service
• Remove the ice bucket and disassemble the crusher housing to access the bearing
• Note the bearing's orientation; transfer any spacers or clips as found
• Reassemble carefully and ensure the auger turns freely by hand before restoring power

A replacement bottle retainer that secures a removable bottle or container inside the refrigerator so it stays stable during normal use. Restores proper positioning to reduce tipping, rattling, and spills. What it does:

• Holds a specific removable bottle or container in place inside the fridge
• Prevents the bottle from shifting, tipping, or banging during door movement
• Helps stop leaks and messes caused by an unsecured bottle
• Addresses symptoms like a loose or broken plastic retainer, audible rattling, or a bottle that won't stay seated

• One retainer-bottle

• Disconnect power to the appliance or unplug the refrigerator before servicing
• Remove refrigerator contents and the affected bottle or shelf to access the retainer
• Typically installs with snap clips or a small fastener; keep original hardware and follow OEM instructions

This replacement bin door restores the front panel for a refrigerator crisper or storage bin, keeping produce secure and improving drawer function. It replaces a cracked or broken door so the bin closes properly. What it does

• Replaces a damaged or cracked bin/front door that won't stay closed
• Restores proper closure so contents stay contained and drawers slide correctly
• Prevents rattling or snagging caused by broken door edges or missing catches
• Helps maintain an even internal compartment by keeping the bin sealed from drawer gaps

• One replacement bin door

• Disconnect power and remove food from the drawer before starting
• Remove the bin/drawer per your manual to access and detach the old door
• Align the replacement door and snap or secure it into the factory mounting tabs; avoid forcing parts
• If you encounter broken mounts or clips, inspect and replace any damaged fasteners for a secure fit

This replacement part is a set screw, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This screw set is compatible in many different areas of the appliance. Screws are typically used for keeping parts of the machinery secure and in place. It is possible that screws can become loose over time and need to be replaced. A new screw set might be needed if the user notices parts of the appliances are becoming loose or are falling off. This can be due to screws becoming stripped over time or if the appliance is bumped during transport. It is typically easy to replace screws. Simply remove the old screw and replace it with a new part. The only tools needed for this repair are a screwdriver and possibly pliers if the damaged screw is stuck in place.Note that this is a genuine OEM replacement part and is sourced from the manufacturer. This set screw is sold individually.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head