Parts for Electrolux FFUE2022AWE: Cabinet Parts

Replacement access panel cover for freezers and refrigerators. Restores finished appearance and protects internal components. Replaces cracked or missing panels.

This is a left-side wire shelf support clip that snaps into the interior wall of the refrigerator or freezer compartment. It holds the wire shelf securely in place at the desired height. Replace this clip if a shelf is sagging, tilting, or no longer stays in position due to a broken or missing support.

Secures wire shelves and baskets in refrigerators and freezers. Replace worn, broken, or missing clips that no longer hold shelves firmly in place.

Hardware screw for securing shelves, bins, and trim panels inside refrigerators and freezers. Replace when stripped, corroded, or missing during repairs.

This replacement access cover restores the appliance's finished appearance while protecting internal components and controls from dust and debris. It helps keep wiring and small parts secure so the unit operates safely. What it does:

• Protects control assemblies, wiring and internal components from dust, spills and accidental contact
• Restores a secure, finished fit when the original cover is cracked, broken or missing
• Helps prevent loose parts from shifting during use and reduces risk of debris-related issues
• Visible damage, a loose or rattling cover, or gaps around the control area are common signs this part is needed

• One replacement access cover

• Disconnect power (unplug or switch off circuit) before starting any work
• Remove necessary trim or panels to access mounting screws; keep fasteners for reassembly
• Handle plastic clips and tabs gently to avoid breakage; use proper tools (screwdriver, trim tool)

This replacement cover is an access panel that protects internal components and keeps the appliance looking finished. It provides a secure barrier to help prevent debris from entering and allows service access when maintenance is needed. What it does

• Covers and protects internal parts from dust, dirt and incidental contact
• Helps reduce airflow of loose debris into the component area
• Provides a finished exterior appearance after repair or service
• Allows access to controls or components when removed
• Fits where the original factory cover was installed

• One replacement cover

• Disconnect power (and gas if applicable) before starting any repair
• Remove fasteners holding the old cover; keep hardware
• Align cover and reinstall screws until snug; do not overtighten
• Use caution: edges may be sharp and panels may be thin

The Air Tower is an OEM part for Frigidaire refrigerators. The cover helps circulate cold air throughout the freezer while also protecting internal components from damage or debris.

Over time, freezer air tower covers can become damaged or discolored due to repeated exposure to cold temperatures and humidity inside the freezer. Signs of a bad cover include cracks, holes, or missing pieces that compromise its ability to properly ventilate the freezer.

Symptoms of a bad freezer air tower cover include:

• Inefficient air circulation leading to warmer freezer temperatures
• Formation of ice buildup around the evaporator coil
• Exposure of internal freezer components to damage or contamination

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This factory screw secures interior or door components in your refrigerator so they stay tight and aligned. Replace missing, stripped, or corroded hardware to eliminate looseness and prevent parts from shifting or rattling during use.

• Fastens brackets, trim, rails, bins, or handles to the cabinet or door
• Restores a secure fit when the original screw is lost, damaged, or rusted
• Helps correct looseness, vibration, and rattling from unsecured parts
• Common symptoms: loose or wobbling handle/trim, misaligned parts, missing hardware

• Disconnect power to the appliance before servicing; turn off water if working near dispenser/ice areas
• Match to the original hardware and install in the same location; reuse any washers/spacers
• Start threads by hand to prevent cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

LED light bulb illuminates refrigerator and freezer compartments for easy food visibility. Replace when dim or burned out. Verify fit with your model.

Light socket holds and connects the bulb in your refrigerator. Replace if lights flicker or won't turn on. Verify fit with your model number.

Replace your broken or missing freezer temperature control knob. This analog dial installs on the control panel for adjusting freezer settings.

This assembly includes a defrost bi-metal thermostat and the accompanying wire harness for a freezer. The thermostat monitors evaporator coil temperature and signals the defrost system to turn on or off, preventing excessive frost buildup. Replace this assembly if the freezer is accumulating heavy frost on the back wall, running too warm, or if the defrost cycle is not activating properly.

This is an upper door hinge for the freezer compartment that supports the door and allows it to open and close smoothly. It mounts at the top of the freezer door and bears the weight of the door assembly. Replace this hinge if the freezer door is sagging, not closing properly, or if the hinge is visibly bent or damaged.

The Fan Mount is an OEM part for Frigidaire refrigerators. It is responsible for holding the evaporator fan in place within the refrigerator's freezer compartment.

A bad fan mount can be caused by regular wear and tear, physical damage, or improper installation. Signs of a faulty fan mount include excessive noise coming from the freezer, reduced cooling performance, or the fan not spinning properly.

Symptoms of a bad fan mount can include:

• Unusual noises coming from the freezer
• Insufficient cooling or uneven temperature
• The evaporator fan not spinning
• Excessive frost or ice buildup in the freezer

Replace your damaged or worn-out fan mount with this genuine OEM part to ensure proper airflow in your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Bottom Hinge is an OEM part for Frigidaire freezers. It is responsible for supporting and allowing the smooth opening and closing of the freezer door.

A bad freezer bottom hinge can be caused by wear and tear, damage, or improper installation. When the bottom hinge becomes faulty, it can result in issues such as difficulty in opening or closing the freezer door, misalignment, or improper sealing.

Symptoms of a bad freezer bottom hinge include:

• The freezer door not closing properly or popping open
• Uneven or misaligned door alignment
• Excessive gaps or air leaks around the door seal
• Unusual noises when opening or closing the door

Replace your faulty freezer bottom hinge with this genuine OEM Frigidaire part to restore  your freezer door. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Bottom door hinge supports and aligns your freezer door for smooth operation and proper sealing. Replace if door sags or won't close flush. Verify fit.

Refrigerator not cooling or freezing over? A failed evaporator fan motor stops air circulation. Straightforward DIY repair restores proper cooling.

Replace a cracked or missing protective trim cover on your freezer or refrigerator. Restores finished appearance and shields internal components from dirt.

This is a plastic cover that serves as a light guide, directing illumination from the LED or light source into the freezer compartment. It mounts over the light assembly and helps distribute light evenly. Replace this cover if it is cracked, yellowed, or broken, which can result in dim or uneven lighting inside the freezer.

If your freezer won't shut off or runs constantly, the reed switch harness may be faulty. This wire harness restores door sensor signals. DIY repair.

Short hex washer head screw for chest freezers, upright freezers, and compact refrigerators. Replaces lost, stripped, or damaged screws to secure panels.

The Freezer Wire Harness is an OEM replacement part for Frigidaire refrigerators. It offers a series of color-coded wires that transmit control signals throughout the freezer compartment. 

Causes of a bad wire harness can involve typical fraying or cracking of insulation from continuous use over time. Rodent damage or accidental cutting during appliance repairs are other potential issues.

Symptoms of a bad freezer wire harness include:

• Lights or other freezer features not functioning properly
• Error codes or control issues with freezer operation  
• Overcooling or warm spots developing in the freezer
• Responsiveness problems with freezer controls and components

This Frigidaire OEM replacement is compatible with some Electrolux, Maytag, and Kenmore models as well.

This replacement cover protects internal components behind the appliance control area and restores a finished appearance. It helps keep wiring and electronics shielded from dust and accidental contact. What it does:

• Shields control and electrical components from dust, debris and incidental contact
• Restores a secure, finished cover where a cracked or missing piece exposes internals
• Helps stop rattling or vibration caused by loose or damaged panels
• Useful when visible damage or gaps allow access to underlying parts

• One replacement cover

• Disconnect power (unplug or shut off breaker) before starting work
• Remove any retaining screws or clips securing the old cover; save fasteners if reuse is possible
• Align the new cover and fasten securely; do not overtighten plastic screws
• If wiring or components were disturbed, restore power cautiously

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.